464209
24
Zoom out
Zoom in
Previous page
1/207
Next page
E-21
MENU
English
Menu structure
4 <SETUP>
Selections
FRONT/TABLE, FRONT/CEILING, REAR/
TABLE, REAR/CEILING
–100 to 0 to +100
FRONT&REAR/FRONT/REAR/OFF
ID 1/ID 2
OFF/ON
OFF/ON
OFF/ON
MONOTONE/COLOR
OFF/ON
LAMP/FAN/RS-232C
9600bps/19200bps/38400bps/57600bps/
115200bps
Increase the value in the positive (+) direction
When the upper part of the image is wider than the lower When the lower part of the image is wider than the top
Decrease the value in a negative () direction
Menu item
LOCATION
S
There are four ways of installing this unit; tabletop or ceiling mounting for front or rear projection. The
DPX-1000 will invert or rotate the projection according to this setting.
KEYSTONE
If the projection unit is at a horizontal or perpendicular angle to the screen the projection image will be
distorted to a trapezoid shape. Use the KEYSTONE setting to electronically correct without increasing
the length of the image. Increase the value when the top of the image is overly wide, and reduce the
value when the lower part of the image is too wide.
REMOTE CONTROL SENSOR
S
Use this parameter for switching between the 2 sensors located on the front and rear of the main unit that
receive signals from the remote control. You can operate the main unit with a wired remote regardless of
how this parameter is set.
REMOTE CONTROL ID
S
The main unit can receive commands from the remote control if you set the same ID in the main unit as
is set by the code change switch on the side of the remote control. Use this code change switch to allow
one remote to control two main units independently.
LENS ADJUSTMENT LOCK
Locks the lens so that the V. POS, ZOOM, and FOCUS settings cannot be changed accidentally. Set to
OFF to cancel this function.
WHITE BOOST
Enhances the luster of the white part in the projected image.
ECONOMY MODE
Lowers power supply to the lamp by approximately 20% to prolong its life.
MENU COLOR
S
Selects the color of the characters and background for the on-screen menu display. Press the + or
button to access the submenu and change color selections.
MESSAGE
Set whether to display messages of any type on screen.
TRIGGER OUT
S
Set the external control TRIGGER OUT terminal 12V signal emission to “LAMP” to synchronize it to
the ON/OFF state of the lamp, to “FAN” to synchronize it to the fan, and to “RS-232C”, to receive ON/
OFF signals through the RS-232C terminal.
BAUD RATE
S
Sets the transmission speed of the RS-232C terminal.
This setting becomes valid from the next time you switch the unit on.
105_DPX-1000(E)16-21 03.3.5, 6:14 PM21
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha DPX-1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha DPX-1000 in the language / languages: German, French, Italian, Spanish as an attachment in your email.

The manual is 5,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha DPX-1000

Yamaha DPX-1000 User Manual - English - 207 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info