593849
43
Zoom out
Zoom in
Previous page
1/57
Next page
4
Assembly/Zusammenbau/Montage/Montaje
iii
VInstall the main keyboard unit.
As shown in the illustration, gently lower the main key-
board unit onto the stand assembly so that the two black
plastic cones protruding from the bottom of the keyboard fit
into the larger holes in the brackets near the rear edge of the
side panels (B). Secure the main keyboard unit to the stand
assembly using two 6 x 14 mm round-head screws 3
screwed through the rear brackets and two 6 x 14 mm round-
head screws 3 through the front blacket.
* When disassembling the Clavinova unscrew the black cones using a
“+” (Phillips) screwdriver.
* Keep your fingers away from the area marked “Danger Zone” in the
illustrations when lowering the main keyboard unit onto the stand
assembly.
BAttach the pedal assembly.
Tilt the main unit as shown in the illustration, align the
pedal assembly with the screw holes on the main unit and
center panel (A), making sure that the pedal cord passes
through the recess in the top of the pedal assembly, and
screw the four 4 x 12 small round-head screws 4 into the
center panel (A), and the two 6 x 14 mm round-head screws
3 into the main keyboard unit.
Plug the pedal cord connector which is protruding from
the top of the pedal assembly into the corresponding connec-
tor in the bottom of the main keyboard unit. Note that the
connector must be inserted with the protruding clip facing
the right end of the keyboard (as seen from the keyboard
side).
6 x 14 mm short round-head screws (black) 3
Kurze 6 x 14 mm Rundkopfschrauben (schwarz) 3
Vis courtes à tête ronde (noires) 6 x 14 mm 3
Tornillos de cabeza redonda cortos de 6 x 14 mm (negros)
3
Danger Zone
Gefahrenzone
Danger
Zona de peligro
Main keyboard unit
Keyboard
Clavier
Unidad principal de teclado
VDas Keyboard montieren.
Setzen Sie das Keyboard, wie in der Abbildung gezeigt,
vorsichtig so auf das zusammengebaute Untergestell, daß die
beiden schwarzen Kunststoffkegel an der Unterseite des Key-
boards in die größeren Bohrungen der Halterungen hinten an
den Seitenwänden (B) greifen. Schrauben Sie das Keyboard
mit zwei 6 x 14 mm Rundkopfschrauben 3 an den hinteren
Halterungen und zwei weiteren 6 x 14 mm
Rundkopfschrauben 3 an den vorderen Halterungen fest.
* Beim Zerlegen des Clavinova können die beiden schwarzen Kegel
mit einem Kreuzschlitzschraubendreher (“+”) herausgedreht werden.
* Halten Sie Ihre Hände beim Aufsetzen des Keyboards auf das
Untergestell von dem in der Abbildung mit “Gefahrenzone”
gekennzeichneten Bereich fern.
BDen Pedalkasten befestigen.
Kippen Sie das Instrument, wie in der Abbildung gezeigt,
und richten Sie den Pedalkasten auf die Schraubenbohrungen
an Keyboard und Verstärkungsstrebe (A) aus. Vergewissern
Sie sich, daß das Pedalkabel richtig in der Nut der
Pedalkastenstrebe liegt, und schrauben Sie den Pedalkasten
dann mit den vier kleinen 4 x 12 mm Rundkopfschrauben 4
an der Verstärkungsstrebe und zwei 6 x 14 mm
Rundkopfschrauben 3 am Keyboard fest.
Schließen Sie den Stecker des Pedalkabels an die Buchse
an der Unterseite des Keyboards an. Beim Einstecken muß
das Klemmstück des Steckers zur rechten Seite des Key-
boards weisen (von der Seite mit der Tastatur aus gesehen).
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha CVP-49 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha CVP-49 in the language / languages: French as an attachment in your email.

The manual is 1,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha CVP-49

Yamaha CVP-49 User Manual - English - 56 pages

Yamaha CVP-49 User Manual - German - 57 pages

Yamaha CVP-49 User Manual - Spanish - 57 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info