48732
174
Zoom out
Zoom in
Previous page
1/196
Next page
174
4Press the [INC/YES] key to save the file. The
message “Completed.” will be displayed after it has
been saved, and you will be returned to the previous
screen.
The save operation will be canceled if you press the
[DEC/NO] key during execution.
When saving a file, the “Card full” message will be
displayed if the space left on the Memory Card is
insufficient. Free up space by deleting unwanted data
and so on, then try saving the file again.
If you enter the name of a file that already exists, you
will see the “Overwrite? Are you sure?” confirmation
message before saving.
Take care not to overwrite important data held on
Memory Card.
File Name Settings
The procedure for renaming files is basically the
same as for renaming Voices. However, you cannot
use symbols or lower case characters, and the name
can only be up to eight characters in length. Details
about renaming Voices are given on Page 80.
Files are named according to the MS-DOS naming
convention. If the file name contains spaces and
other characters unrecognized in MS-DOS, these
characters will automatically be replaced by “_”
(underscore) characters when saving.
Load
You can load files from Memory Card to the
synthesizer is as follows.
Type (File Type)
Settings: all (all data), perf (Performance), all-voice, voice,
chain (Sequence Chain), plugin1, plugin2, all-
pclip (all Phrase Clips), pclip (single Phrase
Clip), WAV (WAV files), AIFF (AIFF files).
The supported WAV/AIFF file formats are as follows.
Format Comments
8bit, linear, mono
16bit, linear, mono
12bit, linear, mono Converted to 16-bit
8bit, linear, stereo 2Phrase Clip created
16bit, linear, stereo 2Phrase Clip created
12bit, linear, stereo Converted to 16-bit, 2Phrase Clips created
Load) Type File:/VOICEDIR/SUBDIR-1/
Card all-voice 001[NEWFILE .S2V]
File Number of
file to be loaded
Data to be loaded
(File Type)
1Use Knob [B] to select the File Type of the data to be
loaded.
2Use Knob [C] to select the File Number.
3When you press the [ENTER] key, the following will
be displayed, depending on the selected File Type.
If you have selected a File Type other than
“perf”, “voice” or “pclip”:
A confirmation message is displayed before loading.
The synthesizer will automatically select an appropriate
location in its internal memory, according to the file type
being loaded.
If you have selected “perf”, “voice” or “pclip” as
the File Type:
You will further have to specify the type of data and
the location to which the file will be loaded.
Use Knobs [B], [C], [1] and [2] to select the file and
the location to which it will be loaded.
Alternatively, you can use the [DATA] knob and the
[DEC/NO] and [INC/YES] keys.
When you press the [ENTER] key, you will see a
confirmation message.
The types of data that you can select for each File
Type, and the locations to which they will be loaded,
are as follows.
perf (Performance)
Settings:
Source Performance Memory:
INT (Internal), EXT (External)
Source Performance Number:
all (all Performances), 1 ~ 128 (INT), 1 ~ 64 (EXT)
Target Performance Memory:
INT (Internal), EXT (External)
Target Performance Number:
all (all Performances), 1 ~ 128 (INT), 1 ~ 64 (EXT)
If you set the source Performance Number to “all,” the
target Performance Number will also be set to “all.”
Load) [Pf:Init Perf ] [Pf:Init Perf ]
Card EXT:064(D16) > INT:128(H16)
Performance Number
of file to be loaded (source)
Performance Number to
which file will be loaded (target)
Performance Memory
of file to be loaded (source)
Performance Memory to
which file will be loaded (target)
Load) Type File:/VOICEDIR/SUBDIR-1/
<< Are you sure? [YES]/[NO] >>
174


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha CS6X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha CS6X in the language / languages: English as an attachment in your email.

The manual is 8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha CS6X

Yamaha CS6X Installation Guide - English - 24 pages

Yamaha CS6X Installation Guide - German - 24 pages

Yamaha CS6X User Manual - German - 196 pages

Yamaha CS6X User Manual - Dutch - 192 pages

Yamaha CS6X User Manual - French - 196 pages

Yamaha CS6X Installation Guide - French - 24 pages

Yamaha CS6X User Manual - Italian - 192 pages

Yamaha CS6X Installation Guide - Italian - 12 pages

Yamaha CS6X User Manual - Portuguese - 284 pages

Yamaha CS6X User Manual - Spanish - 192 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info