27534
42
Zoom out
Zoom in
Previous page
1/54
Next page
40
1
Be careful not to confuse parts, and be sure to install
all parts in the correct direction. Please assemble in
accordance with the sequence given below.
Assembly should be carried out by at least two
persons.
Be sure to use the correct screw size, as indicated
above. Use of incorrect screws can cause damage.
Be sure to tighten up all screws upon completing
assembly of each unit.
The entire package must be turned over during
assembly, so select an area that is large enough for
the unpacking and assembly operation.
Z
Open the carton and remove the parts from
the upper level.
Referring to the illustration, make sure that you have all the
required parts.
Zusammenbau und AufstellungKeyboard Stand Assembly
Cord holders
Kabelhalter
Serre-câble
Soportes de cable
AC power cord
Netzkabel
Cordon dalimentation
Cable de alimentación de CA
A bench may be supplied or optional, depending on
the location in which the instrument was purchased.
X
Attach the three legs (A, B, C).
Use scissors or a cutter to remove the packing material in
which the main unit is wrapped. Then attach the legs to the
bottom of the main unit using four 5 x 20 mm long screws per
leg. Please refer to the illustration carefully when attaching the
legs, to ensure that the positions of the (A) and (B) legs are not
reversed. Also make sure that there is minimum space between
the (A) and (B) leg flanges and the metal frame on the bottom of
the main unit (the screws which attach the legs to this frame will
be installed later, in step
NN
NN
N
).
A
D
CB
Front leg A
Vorderes Standbein A
Pied avant A
Pata frontal A
Front leg B
Vorderes Standbein B
Pied avant B
Pata frontal B
Rear leg C
Hinteres Standbein C
Pied arrière C
Pata trasera C
Pedal box D
Pedalkasten D
Pédalier D
Caja de pedales D
x 20
5 x 20 mm long screws
Lange Schrauben
(5 x 20 mm)
Vis longue 5 x 20 mm
Tornillos largos de 5 x 20 mm
x 2
Achten Sie darauf, die Teile nicht zu verwechseln, und
installieren Sie alle Teile in der richtigen Ausrichtung.
Gehen Sie beim Zusammenbau bitte in der angegebe-
nen Reihenfolge vor.
Die Montage sollte von mindestens zwei Personen
vorgenommen werden.
Achten Sie darauf, die richtige Schraubengröße zu
verwenden, wie es oben gezeigt ist. Die Verwendung
der falschen Schrauben kann zu Schäden führen.
Achten Sie während der Montage darauf, bei jedem
Arbeitsgang alle Schrauben festzuziehen.
Das Instrument wird im Karton zusammengebaut und
muß abschließend zum Aufstellen umgedreht werden.
Achten Sie darauf, daß ausreichend Platz zum Aus-
packen und Aufstellen vorhanden ist.
Z
Den Karton öffnen und die Teile der ober-
sten Lage herausnehmen.
Prüfen Sie anhand der Abbildung, ob die Teile vollzählig
vorhanden sind.
Je nach Vertriebsland wird eine Sitzbank entweder
standardmäßig mitgeliefert oder ist als Sonderzubehör
erhältlich.
X
Die drei Standbeine (A, B und C) montieren.
Entfernen Sie das Verpackungsmaterial an der Unterseite des
Instruments mit einer Schere oder einem anderen
Schneidwerkzeug. Schrauben Sie dann die drei Standbeine mit
jeweils vier langen Schrauben (5 x 20 mm) an das Instrument.
Richten Sie sich bei der Montage der Standbeine bitte nach der
Abbildung — die vorderen Standbeine (A und B) dürfen nicht
vertauscht werden. Achten Sie auch darauf, daß zwischen den
Ansätzen an den vorderen Standbeinen (A und B) und dem
Metallrahmen an der Unterseite des Instruments ein möglichst
kleiner Zwischenraum verbleibt (die Standbeine werden an späte-
rer Stelle, in Schritt
NN
NN
N
, mit diesem Rahmen verschraubt ).
42


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha CLP555 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha CLP555 in the language / languages: Spanish as an attachment in your email.

The manual is 0,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha CLP555

Yamaha CLP555 User Manual - English - 54 pages

Yamaha CLP555 User Manual - German - 54 pages

Yamaha CLP555 User Manual - French - 54 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info