Manual Yamaha CLP-860 (page 52 of 72) (Spanish)

593312

Zoom out

Zoom in

1/72

CLP-880/860/840/820/820S

4 x 20 mm tapping screws 4

4 x 20 mm Schneidschrauben 4

Vis auto-taraudeuses 4 x 20 mm 4

Tornillos de autoenrosque de 4 x 20 mm 4

4 x 12 mm round-head screws 3

4 x 12 mm Halbrundschrauben 3

Vis à tête ronde de 4 x 12 mm 3

Tornillos de cabeza redonda de 4 x 12 mm 3

Attach the rear panel (F).

With the rear panel slightly angled as shown in the illustration,

lower it onto the feet’s protruding edge at the rear of the pedal

box. Then, secure the top of the rear panel to the side panel

brackets using two 4 x 12 mm round-head screws 3 . Finally,

secure the bottom of the rear panel to the pedal box using four 4 x

20 mm tapping screws 4.

Connect the pedal cord.

The pedal cord from the pedal box must be plugged into the

PEDAL connector on the rear of the main unit. Once connected,

attach the cord holders to the rear panel as shown, then clip the

cord into the holders.

Voltage Selector

Before connecting the AC power cord, check the setting of the

voltage selector which is provided in some areas. To set the se-

lector for 110V, 127V, 220V or 240V main voltages, use a “mi-

nus” screwdriver to rotate the selector dial so that the correct

voltage for your region appears next to the pointer on the panel.

The voltage selector is set at 240V when the unit is initially

shipped.

After the proper voltage has been selected connect the AC

power cord. A plug adaptor may be also provided in some areas

to match the pin configuration of the AC wall outlets in your

area.

Montieren Sie die Rückwand (F).

Setzen Sie die Rückwand leicht abgewinkelt, wie in der Abbil-

dung gezeigt, hinter dem Pedalkasten auf die hervorspringenden

Teile der Füße auf. Schrauben Sie dann die Rückwand oben mit

zwei 4 x 12 mm Halbrundschrauben 3 fest. Schrauben Sie die

Rückwand abschließend noch mit vier 4 x 20 mm Schneid-

schrauben 4 an den Pedalkasten.

Schließen Sie das Pedalkabel an.

Das vom Pedalkabel kommende Kabel wird an die PEDAL-

Buchse an der Rückseite der Tastatureinheit angeschlossen. Brin-

gen Sie nach dem Anschluß die Kabelhalter an der Rückwand an,

um das Kabel dann in diese Halter zu klemmen.

Den Spannungswähler einstellen.

Bevor Sie nun das Netzkabel anschließen, müssen Sie den

Spannungswähler (falls vorhanden) auf die örtliche Netzspan-

nung einstellen. Zum Verstellen drehen Sie den Spannungswähler

mit einem Schlitzschraubendreher, bis der richtige Spannungs-

wert (110, 127, 220 oder 240) an der Pfeilmarkierung steht. Bei

der Auslieferung werden alle Instrumente mit Spannungswähler

auf “240” voreingestellt.

Nachdem Sie den Spannungswähler richtig eingestellt haben,

können Sie nun das Netzkabel anschließen. In manchen Gebieten

wird ein Steckerdapter mitgeliefert, um den Anschluß an die evtl.

unterschiedlich geformte Steckdose zu ermöglichen.

Sound coming from speakers is way off is there sn adjustment? Headphones are fine what should I do ? Monitor or upgraded speakers and if speakers which ones and where can I purchase? Thank you john. Submitted on 19-6-2022 at 19:33
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha CLP-860 in the language / languages: Spanish as an attachment in your email.

The manual is 1,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha CLP-860

Yamaha CLP-860 User Manual - English - 72 pages

Yamaha CLP-860 User Manual - German - 72 pages

Yamaha CLP-860 User Manual - Dutch - 69 pages

Yamaha CLP-860 User Manual - French - 72 pages

Yamaha CLP-860 User Manual - Portuguese - 46 pages

Yamaha CLP-860 User Manual - Swedish - 62 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Yamaha CLP-860 Manual

Product: