593311
52
Zoom out
Zoom in
Previous page
1/72
Next page
52
CLP-880/860/840/820/820S
7
F
B
F
4 x 20 mm tapping screws 4
4 x 20 mm Schneidschrauben 4
Vis auto-taraudeuses 4 x 20 mm 4
Tornillos de autoenrosque de 4 x 20 mm 4
4 x 12 mm round-head screws 3
4 x 12 mm Halbrundschrauben 3
Vis à tête ronde de 4 x 12 mm 3
Tornillos de cabeza redonda de 4 x 12 mm 3
M
Attach the rear panel (F).
With the rear panel slightly angled as shown in the illustration,
lower it onto the feet’s protruding edge at the rear of the pedal
box. Then, secure the top of the rear panel to the side panel
brackets using two 4 x 12 mm round-head screws 3 . Finally,
secure the bottom of the rear panel to the pedal box using four 4 x
20 mm tapping screws 4.
<
Connect the pedal cord.
The pedal cord from the pedal box must be plugged into the
PEDAL connector on the rear of the main unit. Once connected,
attach the cord holders to the rear panel as shown, then clip the
cord into the holders.
>
Voltage Selector
Before connecting the AC power cord, check the setting of the
voltage selector which is provided in some areas. To set the se-
lector for 110V, 127V, 220V or 240V main voltages, use a “mi-
nus” screwdriver to rotate the selector dial so that the correct
voltage for your region appears next to the pointer on the panel.
The voltage selector is set at 240V when the unit is initially
shipped.
After the proper voltage has been selected connect the AC
power cord. A plug adaptor may be also provided in some areas
to match the pin configuration of the AC wall outlets in your
area.
M
Montieren Sie die Rückwand (F).
Setzen Sie die Rückwand leicht abgewinkelt, wie in der Abbil-
dung gezeigt, hinter dem Pedalkasten auf die hervorspringenden
Teile der Füße auf. Schrauben Sie dann die Rückwand oben mit
zwei 4 x 12 mm Halbrundschrauben 3 fest. Schrauben Sie die
Rückwand abschließend noch mit vier 4 x 20 mm Schneid-
schrauben 4 an den Pedalkasten.
<
Schließen Sie das Pedalkabel an.
Das vom Pedalkabel kommende Kabel wird an die PEDAL-
Buchse an der Rückseite der Tastatureinheit angeschlossen. Brin-
gen Sie nach dem Anschluß die Kabelhalter an der Rückwand an,
um das Kabel dann in diese Halter zu klemmen.
>
Den Spannungswähler einstellen.
Bevor Sie nun das Netzkabel anschließen, müssen Sie den
Spannungswähler (falls vorhanden) auf die örtliche Netzspan-
nung einstellen. Zum Verstellen drehen Sie den Spannungswähler
mit einem Schlitzschraubendreher, bis der richtige Spannungs-
wert (110, 127, 220 oder 240) an der Pfeilmarkierung steht. Bei
der Auslieferung werden alle Instrumente mit Spannungswähler
auf “240” voreingestellt.
Nachdem Sie den Spannungswähler richtig eingestellt haben,
können Sie nun das Netzkabel anschließen. In manchen Gebieten
wird ein Steckerdapter mitgeliefert, um den Anschluß an die evtl.
unterschiedlich geformte Steckdose zu ermöglichen.
52


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha CLP-840 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha CLP-840 in the language / languages: French as an attachment in your email.

The manual is 1,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha CLP-840

Yamaha CLP-840 User Manual - English - 72 pages

Yamaha CLP-840 User Manual - German - 72 pages

Yamaha CLP-840 User Manual - Dutch - 69 pages

Yamaha CLP-840 User Manual - Portuguese - 46 pages

Yamaha CLP-840 User Manual - Swedish - 62 pages

Yamaha CLP-840 User Manual - Spanish - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info