18181
98
Zoom out
Zoom in
Previous page
1/106
Next page
E-92
SYMPTOM
This unit does not turn on
when POWER is pressed.
Playback does not begin
with the CD loaded.
Playback is delayed, or
begins at the wrong place.
Recording/copying is not
possible.
Some vibration and rotation
noise are created during the
copying.
Continuous recording
cannot be made on a disc on
the HDD beyond 100
minutes.
The beginning of the track
is missing during the
playback when this unit is
connected digitally to an
amplifier.
The sound is missing when
this unit switches one disc
to another.
A CD-R or CD-RW that has
been recorded with this unit
cannot be played on the
other CD player or DVD
player.
Sound skips.
This unit makes noise.
If this unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures
suggested. If they cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your
authorized YAMAHA dealer or service center for assistance.
CAUSE
The power cable is not completely connected.
There is moisture on the laser pick-up.
The CD has been loaded upside down.
The CD is dirty.
The CD may be scratched or damaged.
The CD-R or CD-RW disc has been finalized.
The CD-R or CD-RW disc that has completed
recording is loaded.
INPUT is not correctly set.
Further digital recording or copying has been
attempted from the digitally copied sources.
There is not enough available space left or 99
tracks have already been recorded on the disc.
There is no available space on the HDD.
If the power cable was unplugged or there
was a power outage during recording, the
recorded material may be lost.
The CD-R or CD-RW disc is dirty or
damaged.
The HDD is not installed properly.
This unit copies by rotating the CD, CD-R or
CD-RW disc at high speed.
The maximum recordable time for a disc on
the HDD is 99 minutes 59 seconds.
The tracks that have different emphases have
been played.
The titles appear on the display during the
playback of the part that has been recorded
stretching over the two discs.
Your CD or DVD player is not compatible
with CD-R or CD-RW discs.
The CD-R or CD-RW disc has not been
finalized.
This unit and/or the component connected is
being subjected to vibration or impact.
The CD is dirty.
Connection has not correctly been made.
REMEDY
Securely connect the power cable.
Turn the power of this unit and wait 20 to 30 minutes
before trying to play.
Reload the CD with the label side facing up.
Clean the CD.
Check the CD carefully. Replace it if necessary.
Load a recordable CD that has not been finalized yet.
Load a recordable CD.
Set INPUT to the correct position according to the input
signal.
Switch to ANALOG to make a recording.
Load a recordable disc (for a CD-R or CD-RW disc).
Select the other discs (for the HDD).
Erase the space not being used to create available space on
the HDD for further recording.
If the recording of a CD-RW disc is interrupted, try
recording again from the beginning. When the recording of
a CD-R disc is interrupted, start recording over again with
a disc that can be recorded on.
Clean or replace the CD-R or CD-RW disc.
Install the HDD properly following the attached instruc-
tion.
Lower the copying speed to decrease vibration and rotation
noise.
Regardless of the recording mode, the recording will be
performed continuously to the next available disc after the
recording has been performed to one disc for its maximum
length.
Connect to the amplifier using the ANALOG LINE OUT
(PLAY) jacks.
Press TEXT/TIME to switch the display to the indication
of time.
Use a CD or DVD player compatible with CD-R or CD-
RW discs.
Finalize the CD-R or CD-RW disc.
Relocate the unit. (This is not possible if the skipping
sound is already on the recording due to vibrations or
impact that occurred during recording.)
Clean the CD.
Properly connect the audio pin cables. Replace the audio
cables.
TROUBLESHOOTING
110_HD1300(E)84-94 02.6.24, 6:52 PM92
98


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha CDRHD1300E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha CDRHD1300E in the language / languages: English as an attachment in your email.

The manual is 2,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha CDRHD1300E

Yamaha CDRHD1300E User Manual - German - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info