19268
27
Zoom out
Zoom in
Previous page
1/40
Next page
25
EnglishREMOTE CONTROL APPENDIXPREPARATION OPERATION
OPERATING OTHER COMPONENTS USING THE REMOTE CONTROL
6 Point the remote control at the component to
be controlled (the component turned on in
step 1) and press p repeatedly until the
component’s power turns off.
If the transmission indicator flashes twice, this
indicates that you have cycled through all the codes
stored in the memory of the remote control. Up to 300
manufacturer codes (for TV) may be stored in the
memory of the remote control. Since a manufacturer
code is set by pressing p and cycling in order through
these codes, you may need to press p up to 300 times
to reach the proper code.
y
Up to 120 manufacturer codes for VCR, 170 for satellite tuner and
20 for cable TV may be stored in the memory of the remote control.
Note
If you accidentally press p too many times after the power is
turned off, you may press m the same number of times to go
through the manufacturer codes in reverse order. The correct
manufacturer code will not be set unless you do this.
7
6
7 Press the remote control selector button you
pressed in step 2.
The indicator will go out.
The transmission indicator will go out once auto preset
has been performed properly.
Note
During step 6, if you press p about 300 times and the
transmission indicator flashes twice slowly and the component’s
power still has not turned off, this indicates that auto preset
cannot be performed for the component in question. Check that
the component to be controlled supports remote control operation.
You may also try performing manual preset.
Precautions when performing
preset
The transmission indicator will go out once the
manufacturer code has been set properly.
If the transmission indicator does not go out, or if it flashes
and then goes out, repeat the procedure from step 1. Pay
attention to the following points when you repeat the preset
procedure.
Check the manufacturer code number.
Check that the correct remote control selector button has
been selected when setting the manufacturer code.
If more than one code is given for a manufacturer, try
entering each code in the order given.
Remove and replace the remote control’s batteries
(complete this step within 2 minutes) and then repeat the
procedure.
To clear a manufacturer code
Perform the procedure “Using manual preset” described on
page 23 and enter the following codes when you reach
step 3.
To clear the “TV” button: 0000
To clear the “VCR” button: 0000
To clear the “SAT” button: 0000
To clear all buttons for “TV”, “VCR” and “SAT”: 9990
Transmission
indicator
0105AV-S70_23-30_EN 3/29/0, 4:04 PM25
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha AVS70 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha AVS70 in the language / languages: English as an attachment in your email.

The manual is 1,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info