48726
105
Zoom out
Zoom in
Previous page
1/147
Next page
105
Chapter 19 Master Class 2 — Advanced Music Production
88 Recording AN200 knob moves to a sequencer
Have you got an external sequencer or computer? And are you using the AN200 as a synthesizer (as we
covered in Tip 86) to play back your sequencer tracks? If so, here’s a power-user Tip for you that will give
you undreamed-of control over the sound.
Here, you’ll learn how to record all your knob moves and button presses to your sequencer. Which means
when you play back your song, all the changes you make to the Voice automatically play back, too. It’s like
having an second Free EG function (page 60) — but with an unlimited amount of tracks to work with.
The following procedure is a bit complicated — in that many of the instructions depend on the settings and
capabilities of your particular sequencer, and how familiar you are with them. If you find yourself in deep
water, refer to the relevant owner’s manual.
1 Connect the AN200 and the external sequencer as shown.
2 Set up the sequencer appropriately for receiving the control data and for
playing the AN200.
Specifically, make sure that:
All MIDI channel settings are correct. The tracks for playing the AN200 should be set to the same
MIDI channel as the Synth track. By default, the Synth track is set to receive over Channel 1, though
this can be changed on the AN200 (see page 97).
The track or tracks having note data are properly set to play, and that a new track (for the knob moves)
is set to record.
3 While listening to the playback, tweak the knobs of
the AN200.
If everything’s been set up properly, every move you make will be recorded
as Control Change data. (For information on the parameters and their cor-
responding Control Change numbers, refer to the MIDI Data Format.)
The AN200 also lets you choose between having a full parameter set for
control, or a limited one. (See Tech Talk below.)
4 Stop the song and play it back to hear your recorded
changes.
Go on to record more knob moves to additional tracks on the sequencer, if
you want.
Any function called “MIDI Thru” or “MIDI Echo” on the sequencer is set to “off.” If the
sequencer’s MIDI Thru is on, you could get unwanted double data.
If you’re recording the same knob to different tracks, you may want to mute previous
tracks as you go along. Also, be aware that too many knob moves and button presses
could clog the data flow and result in glitches or undesirable changes in the sound.
MIDI
OUT
MIDI
IN
MIDI
IN
MIDI
OUT
AN200 Computer
Sequence
software
Control Change In/Out
Determines whether the AN200 uses a limited
set of parameters for sending and receiving
Control Change data, or a full set. (For details
on available parameters and their assign-
ments, refer to the MIDI Data Format.)
Hold down [SHIFT] and press button [14]
(MIDI SETUP), repeatedly if necessary, until
CCio” appears in the display. Use the
[DATA] knob to change the setting.
Settings
norm (Normal)
Enables Control Change in/out for the
limited parameter set.
ALL (All)
Enables Control Change in/out for the full
parameter set.
105


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha AN200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha AN200 in the language / languages: English as an attachment in your email.

The manual is 6,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha AN200

Yamaha AN200 User Manual - German - 147 pages

Yamaha AN200 User Manual - Dutch - 120 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info