516980

Yamaha A-S300 Manual

6
Zoom out
Zoom in
Previous page
1/150
Next page
CONTROLS AND FUNCTIONS
4 En
1 CD input jacks
Used to connect a CD player (see page 5).
2 PHONO jacks and GND terminal
Used to connect a turntable that uses an MM cartridge,
and to ground the terminal (see page 5).
3 Audio input/output jacks
Used to connect external components, such as a tuner, etc
(see page 5).
4 DOCK jack
Used to connect an optional Yamaha Universal Dock for
iPod or Wireless System for iPod (see page 10).
5 SUBWOOFER OUT jack
Used to connect a subwoofer with built-in amplifier (see
page 5).
y
The SUBWOOFER OUT jack attenuates signals over 90 Hz.
6 POWER MANAGEMENT switch
Enables or disables the automatic power down function
(see page 7).
7 SPEAKERS A/B terminals
Used to connect one or two speaker sets (see page 5).
8 VOLTAGE SELECTOR switch
(Taiwan and Central/South America models
only)
The VOLTAGE SELECTOR switch must be set to your
local main voltage before plugging the power cable into
the wall outlet (see page 7).
9 IMPEDANCE SELECTOR switch
See IMPEDANCE SELECTOR switch on this page.
0 Power cable
Connect the power cable into the wall outlet (see page 7).
■ IMPEDANCE SELECTOR switch
Do not change the IMPEDANCE SELECTOR switch
while the power of this unit is turned on, as doing so may
damage the unit.
If the unit fails to turn on, the IMPEDANCE SELECTOR
switch may not be fully slid to either position. If this is the
case, remove the power cable and slide the switch all the
way to either position.
Select the switch position (LOW or HIGH) according to
the impedance of the speakers in your system.
Rear panel
(Taiwan and Central/South America models)
CAUTION
Switch
position
Impedance level
HIGH
• If you use one set (A or B), the impedance of
each speaker must be 6
Ω or higher.
• If you use two sets (A and B) simultaneously,
the impedance of each speaker must be 12
Ω
or higher.
• If you make bi-wire connections, the
impedance of each speaker must be 6
Ω or
higher. See page 6 for details.
LOW
• If you use one set (A or B), the impedance of
each speaker must be 4
Ω or higher.
• If you use two sets (A and B) simultaneously,
the impedance of each speaker must be 8
Ω or
higher.
• If you make bi-wire connections, the
impedance of each speaker must be 4
Ω or
higher. See page 6 for details.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha A-S300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha A-S300 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 5,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info