517061
39
Zoom out
Zoom in
Previous page
1/89
Next page
34 02R Applications
Yamaha 02R & 03D Applications Guide
12
Two 02Rs with Four DA-88s
This application shows how two 02Rs can be used with four Tascam DA-88s to create a
48-input, 32-track digital recording system. The 32 digital tape returns and 48 Mic/Line
inputs provide up to 80 inputs at mixdown.
The two 02Rs are cascaded together using a 25-pin straight cable and two CD8-CS Cascade
cards, which are installed in Slot [3] of each 02R (could be Slot [4]). The cascade
connection carries the eight buses, any four of the eight AUX buses, Stereo bus, and Solo
bus. This allows both consoles to work together as one large 80-input mixing console. The
master section of 02R–B is used for monitoring and two-track operations. The studio
monitors and two-track recording equipment are also connected to this 02R.
Connections
The Tascam (CD8-TD) cards must be screwed securely in place. Do not leave the screws
out after installation as the cards will not be grounded correctly.
DA-88–A is connected to Slot [1] of 02R–A and the tape inputs correspond to tracks one
through eight (Tape In 1–8). DA-88–B is connected to Slot [2] of 02R–A and the tape
inputs correspond to tracks nine through sixteen (Tape In 9–16). DA-88–C is connected
to Slot [1] of 02R–B and the tape inputs correspond to tracks 17 through 24 (Tape In
1–8). DA-88–D is connected to Slot [2] of 02R–B and the tape inputs correspond to
tracks 25 through 32 (Tape In 9–16). PW-88DL cables are available from Tascam.
The optional SY-88 Sync Board is required for DA-88–A. This enables the dedicated
timecode track, which can be re-striped at anytime, and provides SMPTE timecode and
MTC outputs. A timecode offset can be specified on DA-88–A.
02R Wordclock Setup
On the DIGITAL I/O menu, the wordclock source should be set to W.CLK.
DA-88 Wordclock Setup
DA-88–A works as wordclock master. Wordclock is fed to the 02R using a BNC to BNC
cable, and to the other DA-88s using PW-88S 15-pin sync cables, available from Tascam.
The sampling rate is set when the DA-88 tapes are formatted. This can be either 48 kHz or
44.1 kHz. After formatting, the sampling rate is determined by the formatted tape.
Notes
The DA-88s must be powered up even when they are not being used. Failure to do so may
cause an intermittent pumping noise on the 02R.
DA-88–A is set to MACHINE ID to 0, DA-88–B to MACHINE ID to 1, DA-88–C to
MACHINE ID 2, and DA-88–D to MACHINE ID 3. Since DA-88–A works as the
Control Master, it should be used for synchronized transport and locate operations.
The optional Tascam SY-88 Sync Board must be installed in DA-88–A to use SMPTE
timecode and MTC. This is available from Tascam. The other DA-88s do not require
SY-88 Sync Boards and their tapes do not have to be striped with timecode. They are
synchronized to DA-88–A via the PW-88S 15-pin sync cables.
The terminator bundled with a PW-88S sync cable should be connected to the SYNC
OUT on DA-88–D to ensure reliable synchronization.
The rear panel of the SY-88 Sync Board has a DIP switch labeled MODE. Set DIP
switches 2 and 5 to ON (O). Set internal switch 8 on the SY-88 board marked S2 to ON.
To use the MTC function, the SY-88 firmware must be version 3.08 or higher.
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha 03D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha 03D in the language / languages: English as an attachment in your email.

The manual is 2,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha 03D

Yamaha 03D User Manual - German - 307 pages

Yamaha 03D User Manual - Dutch - 302 pages

Yamaha 03D User Manual - French - 300 pages

Yamaha 03D User Manual - Italian - 301 pages

Yamaha 03D User Manual - Portuguese - 141 pages

Yamaha 03D User Manual - Spanish - 315 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info