517061
33
Zoom out
Zoom in
Previous page
1/89
Next page
28 02R Applications
Yamaha 02R & 03D Applications Guide
9
02R with One DA-88
This application shows how the 02R can be used with a Tascam DA-88 to create a 24-input,
8-track digital recording system. The eight digital tape returns and 24 Mic/Line inputs
provide up to 32 inputs at mixdown. In addition, the 02R’s built-in automation and scene
memory systems provide both dynamic and static mix automation referenced to timecode.
Connections
The Tascam (CD8-TD) card must be screwed securely in place. Do not leave the screws
out after installation as the card will not be grounded correctly.
The Tascam digital audio cable (PW-88DL) carries the eight tape sends and eight tape
returns.
The DA-88 is connected to Slot [1] of the 02R. These tape inputs correspond to tracks
one through eight.
The optional SY-88 Sync Board is required. The DA-88 has a dedicated timecode track
and can output SMPTE timecode or MTC. In addition, a timecode offset can be
specified on the DA-88, so the 02R automix start time can be adjusted. The DA-88 also
has the ability to re-stripe the timecode track.
The 75 ohm wordclock termination switch on the back of the 02R is set to ON.
02R Wordclock Setup
On the DIGITAL I/O menu, the wordclock source should be set to W.CLK.
DA-88 Wordclock Setup
The DA-88 works as wordclock master. Wordclock is fed to the 02R using a BNC to BNC
cable. The sampling rate is set when the DA-88 tape is formatted. This can be either 48 kHz
or 44.1 kHz. After formatting, the sampling rate is determined by the formatted tape.
Notes
The DA-88 must be powered up even when it is not being used. Failure to do so may
cause an intermittent pumping noise on the 02R.
On the DA-88 rear panel, set the MACHINE ID to 0.
The optional Tascam SY-88 Sync Board must be installed to use SMPTE timecode and
MTC. This is available from Tascam.
The rear panel of the SY-88 Sync Board has a DIP switch labeled MODE. Set DIP
switches 2 and 5 to ON (O). Set internal switch 8 on the SY-88 board marked S2 to ON.
To use the MTC function, the SY-88 firmware must be version 3.08 or higher.
On the Tascam (CD8-TD) card there is a DIP switch that should be set to 16-bit. This is
the initial setting, but you should confirm it. This switch is for use with Tascam High-Bit
recording applications.
Tascam 25-pin digital audio cables PW-88DL (5 m) and PW-88D (1 m) are available
from Tascam.
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha 03D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha 03D in the language / languages: English as an attachment in your email.

The manual is 2,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha 03D

Yamaha 03D User Manual - German - 307 pages

Yamaha 03D User Manual - Dutch - 302 pages

Yamaha 03D User Manual - French - 300 pages

Yamaha 03D User Manual - Italian - 301 pages

Yamaha 03D User Manual - Portuguese - 141 pages

Yamaha 03D User Manual - Spanish - 315 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info