517061
27
Zoom out
Zoom in
Previous page
1/89
Next page
22 02R Applications
Yamaha 02R & 03D Applications Guide
6
Two 02Rs with Four ADATs & BRC
This application shows how two 02Rs can be used with four Alesis ADATs and a BRC Master
Remote Control to create a 48-input, 32-track digital recording system. The 32 digital tape
returns and 48 Mic/Line inputs provide up to 80 inputs at mixdown. In addition, the 02Rs
built-in automation and scene memory systems provide both dynamic and static mix
automation referenced to timecode.
The two 02Rs are cascaded together using a 25-pin straight cable and two Cascade
(CD8-CS) cards, which are installed in Slot [3] of each 02R (could be Slot [4]). The
cascade connection carries the eight buses, any four of the eight AUX buses, Stereo bus, and
Solo bus. This allows both consoles to work together as one large 80-input mixing console.
The master section of 02R–B is used for monitoring and two-track operations. The studio
monitors and two-track recording equipment are also connected to this 02R.
Connections
The ADAT (CD8-AT) and Cascade (CD8-CS) cards must be screwed securely in place.
Do not leave the screws out after installation as the cards will not be grounded correctly.
The Digital In/Out connectors on the 02R and ADAT are connected together using the
Optical Cable. Press the DIGITAL IN buttons on the ADATs to use the DIGITAL IN.
ADAT–A is connected to Slot [1] of 02R–A and the tape inputs correspond to tracks one
through eight. ADAT–B is connected to Slot [2] of 02R–A and the tape inputs
correspond to tracks nine through sixteen. ADAT–C is connected to Slot [1] of 02R–B
and the tape inputs correspond to tracks 17 through 24. ADAT–D is connected to Slot
[2] of 02R–B and the tape inputs correspond to tracks 25 through 32.
The Alesis BRC Master Remote Control can control up to 16 ADATs (i.e. 128 tracks).
The BRC provides ADAT timecode to SMPTE timecode conversion. In addition, a
timecode offset can be specified, so the automix start time can be adjusted.
The 75 ohm wordclock termination switches on both 02Rs is set to ON.
02R Wordclock Setup
On the DIGITAL I/O menu, the wordclock source should be set to W.CLK.
ADAT & BRC Wordclock Setup
The BRC works as wordclock master and the four ADATs follows it automatically via the
9-pin sync cables. The sampling rate can be set to either 48 kHz or 44.1 kHz. Use Fixed
mode for 48 kHz and Variable mode for 44.1 kHz (using the PITCH DOWN button, set to
–147 cents. At which point “–146, 44.1, –148” appears on the display). The newer ADAT-XT
has dedicated switches for selecting these two sampling rates.
Notes
The ADATs must be powered up before the BRC and in the following order: D, C, B, A.
This is because when the BRC is powered up it checks how many ADATs are connected,
allocates them device numbers, and automatically sets the system clock.
The rear of the Cascade (CD8-CS) cards have an IN/OUT switch. On 02R–A is set to
OUT. On 02R–B it is set to IN.
To generate timecode on the BRC, press the GEN SYNC button.
The optional CD8-CS kit contains two CD8-CS cards and one 25-pin straight cable.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha 03D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha 03D in the language / languages: English as an attachment in your email.

The manual is 2,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha 03D

Yamaha 03D User Manual - German - 307 pages

Yamaha 03D User Manual - Dutch - 302 pages

Yamaha 03D User Manual - French - 300 pages

Yamaha 03D User Manual - Italian - 301 pages

Yamaha 03D User Manual - Portuguese - 141 pages

Yamaha 03D User Manual - Spanish - 315 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info