559199
20
Zoom out
Zoom in
Previous page
1/350
Next page
20 Chapter 2—Control Surface & Rear Panel
02R96 Version 2—Owner’s Manual
AD Input Section
AD Input #1 is shown at the top; AD Inputs #17 and #18 below.
A +48V ON/OFF switches (AD 1–16)
These switches turn on and off the +48 V phantom power feed to each INPUT A
(XLR-type connector). Phantom power is typically used to power condenser-type
microphones or direct boxes. See “Phantom Power (AD 1–16)” on page 53 for
more information.
B PAD switches (AD 1–16)
These switches turn on and off the 26 dB pad (attenuator) for each AD Input. See
“Pad (AD 1–16)” on page 53 for more information.
C GAIN controls
These controls adjust the gain of the AD Input Head Amps. They have an input
sensitivity of –16 dB to –60 dB or +10 dB to –34 dB when Pad is on. AD Inputs 17
to 24 have an input sensitivity of +10 dB to –34 dB. See “Gain on page 53 for
more information.
D PEAK indicators
These indicators light up when the input signal level is 3 dB below clipping. See
“PEAK & SIGNAL Indicators on page 53 for more information.
E SIGNAL indicators
These indicators light up when the input signal level is 20 dB below nominal. See
“PEAK & SIGNAL Indicators on page 53 for more information.
F INSERT ON/OFF switches (AD 1–16)
These switches are for turning on and off the AD Input inserts. See AD Inserts
(AD 1–16)” on page 54 for more information.
Channel strips
Channel strip #1 is shown here.
The function of each channel strip depends on the currently selected Layer. See
Selecting Layers on page 47 for more information.
A Encoders
These controls are used to edit Input and Output Channel parameters. Their exact
operation depends on the currently selected Encoder mode and Layer. There are
two preset Encoder modes, Pan and Aux, and two assignable modes, with over 40
parameters to choose from. See Selecting Encoder Modes” on page 50 for more
information.
The Encoders feature push switches that are used to punch the parameter cur-
rently assigned to the Encoders in and out during Automix recording. See
“Punching In & Out Individual Parameters on page 183 for more information.
B AUTO buttons
These buttons are used to set Automix recording and playback for each channel.
Their exact operation depends on the currently selected Layer. Their indicators
light up orange in Record-Ready mode, red while recording, and green during
playback. See Channel Strip [AUTO] Buttons on page 174 for more information.
C SEL buttons
These buttons are used to select Input and Output Channels for editing with the
SELECTED CHANNEL section. Their exact operation depends on the currently
selected Layer. The [SEL] button indicator of the currently selected channel lights
up. See “Selecting Channels” on page 48 for more information. The [SEL] buttons
can also be used to pair channels, and to add and remove channels to and from the
EQ, Comp, Fader, and Mute groups.
1
2
3
4
5
6
1
ON
OFF
OFF
ON
26dB
-16
-60
GAIN
PEAK
SIGNAL
INSERT
+
48V
PAD
3
4
5
GAIN
34
10
+
GAIN
34
10
+
PEAK
SIGNAL
17 18
18
17
25
49
1
1
50
40
30
20
15
10
10
5
0
5
ON
SOLO
SEL
AUTO
1
2
3
4
5
6
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha 02R96VCM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha 02R96VCM in the language / languages: English as an attachment in your email.

The manual is 4,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha 02R96VCM

Yamaha 02R96VCM User Manual - German - 357 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info