517047
28
Zoom out
Zoom in
Previous page
1/71
Next page
28 Connections and Setup
01V96i—Owner’s Manual
Specifying the Wordclock
Source
To digitally connect the 01V96i to external devices, you
must specify the wordclock source for the system. Fol-
low the steps below.
1. Press the DISPLAY ACCESS [DIO/SETUP]
button repeatedly until the DIO/Setup |
Word Clock page appears.
On this page, you can view the current synchroni-
zation status of input signals at each slot and con-
nector.
The source select button indicators are explained
below:
A usable wordclock signal is present at this
input, and it is in sync with the current 01V96i
internal clock.
No wordclock signal is present at this input.
A usable wordclock signal is present at this
input, but it is out of sync with the current
01V96i internal clock.
This input is the currently-selected wordclock
source.
This input was selected as the wordclock
source, but no usable signal was received.
Either this input is not receiving wordclock, or
else it cannot be used with the cur-
rently-installed I/O card.
2. Use the cursor buttons to move the cur-
sor to a source, then press [ENTER].
The following are possible wordclock sources.
However, USB only displays the synchronization
status, and cannot be selected as the wordclock
master.
•SLOT
These buttons select the inputs from the digital I/O
card installed in the slot as the wordclock source.
Inputs are selected in pairs (odd and even numbers
in this order). The SLOT TYPE column displays the
names of any installed I/O card. The number of
pairs depends on the type of I/O card installed.
•adat
These buttons select the inputs from the ADAT IN
connector on the rear panel. Inputs are selected in
pairs (odd and even numbers in this order).
•WC IN
This button selects the wordclock signal input at the
WORD CLOCK IN connector on the rear panel.
•2TRD
This button selects the 2TR IN DIGITAL input as
the wordclock source.
INT 44.1k, INT 48k, INT 88.2k, INT 96k
These buttons select the internal clock generator as
the wordclock source. The 01V96i will function as
the wordclock master.
•USB (display only)
This indicates the synchronization status of the sig-
nal being input from the TO HOST USB port. It
cannot be selected as the wordclock master.
Note: When you change the wordclock settings on any
device in your digital audio system, some devices may out-
put noise due to being out of synchronization. Be sure to
turn down your monitoring device before changing word-
clock settings.
Tip:
The FS box displays the sampling frequency at which the
01V96i is currently operating.
The SLOT TYPE column displays the names of any
installed I/O card.
The IN and OUT columns indicate the number of input
and output channels available for each installed I/O
card.
Note: To transfer data at higher sampling frequencies
(88.2 kHz or 96 kHz) between the 01V96i and connected
external devices, you need to set the data transfer format.
Tip: If wordclock transfer is interrupted while the 01V96i
(being used as a slave unit) is receiving the clock signal, the
unit will automatically switch to an internal clock (INT
44.1k/ INT 48k/INT 88.2k/INT 96k) that is closest to the
interrupted clock.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha 01V96i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha 01V96i in the language / languages: English as an attachment in your email.

The manual is 5,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha 01V96i

Yamaha 01V96i Quick start guide - English - 32 pages

Yamaha 01V96i User Manual - German - 71 pages

Yamaha 01V96i User Manual - French - 71 pages

Yamaha 01V96i User Manual - French - 34 pages

Yamaha 01V96i User Manual - Portuguese - 71 pages

Yamaha 01V96i User Manual - Spanish - 71 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info