655219
14
Zoom out
Zoom in
Previous page
1/20
Next page
14
Reset Key Pad code
If the Key Pad code is accidentally forgotten, the Key Pad
can be reset to factory default (0000) using the following
steps:
1. Unscrew the two Key Pad case screws and remove Key
Pad back cover (please disable tamper rst).
Locate and remove the battery. See battery change
section (16-17)
2. Press the number ‘4’ key at the same time as reinserting
the battery.
3. Screw the Key Pad case together and re-learn the Key
Pad into the system using the steps described above in
this section.
Using your Key Pad
The Key Pad can be used to Away Arm and Home Arm
the system using the buttons as shown.
The system is disarmed by pressing the disarm button
followed by your PIN code.
An emergency alarm can be activated by pressing the
panic A and B buttons simultaneously. Deactivate panic
event by pressing the disarm button followed by your PIN
code.
If there is a system fault, you will need to press the Arm/
Home Arm button for a second time to “force arm” the
system.
Using your Smoke Detector
Smoke Detection
When smoke is detected the device will activate for a
minimum of 10 seconds with a two tone alarm and ashing
LED. The Detector will send a radio signal to the Smart
Hub. You will then be notied via a push notication, SMS
and email .
Pressing the test button when in an alarm condition will
silence the alarm for 10 minutes. It will automatically
resume smoke detection again after this period.
Testing
Smoke Detector testing should be done on a regular
monthly basis. Pressing the test button will make the LED
ash, the audible sounder chime and will send a radio
test signal to the Smart Hub when the button is released.
If nothing happens after pressing the test button, it
indicates the batteries will need changing.
Recalibration
The Smoke Detector might need recalibrating after time
to ensure it is working at its optimum. This is done by
pressing and holding the test button until the LED ashes
and beeps after 10 seconds. The Detector will then start
its self calibration routine.
Using your Panic Button
Activate an Alarm
Press and hold the red button for at least 3 seconds. The
LED will light momentarily and the alarm will be activated.
Silence an Alarm
1. Press and hold down the red button for 10 seconds.
The LED will light momentarily for a second time and the
alarm will be silenced.
2. Please note that silencing the alarm with the Panic
Button does not reset the system. If the alarm is armed
prior to activation, the system will re-arm after being
silenced with the Panic Button.
3. The system will require a reset at the Smart Hub after
being silenced with the Panic Button.
Using Accessories (cont.)
7
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yale SR330 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yale SR330 in the language / languages: English as an attachment in your email.

The manual is 2,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info