478480

Yaesu VX-150 Manual

9
Zoom out
Zoom in
Previous page
1/44
Next page
VX-150 OPERATING MANUAL 7
FREQUENCY NAVIGATION
Press the
[
VFO
(
PRI
)
]
button, if necessary, to select the VFO mode. The VX-150 has two
VFOs, labeled “A” and “B,” either of which can be used for all of the procedures described
in this manual. You can change VFOs with the
[
VFO
(
PRI
)
]
button at any time.
There are several ways to tune the VX-150: in selectable channel steps or 1 MHz steps
with the
[
s
]
/
[
t
]
keys or DIAL knob, and direct keypad frequency entry.
Use the DIAL knob to tune the displayed VFO frequency at the current channel step rate.
You can also press the
[
s
]
/
[
t
]
keys momentarily to do this.
To change the MHz range of the VFO, you can press the
[
F
]
key followed by an
[
s
]
or
[
t
]
key (or turn the DIAL knob). Note the beeps when using the
[
s
]
/
[
t
]
keys when
moving up or down. When done, press
[
F
]
again, or just wait five seconds.
You can also enter a frequency directly just by keying in the 1 MHz and the kHz digits. If
you are using 5 kHz steps enter five digits. Otherwise, just four digits will do. Partial
entries can be completed using the
[
VFO
(
PRI
)
]
key.
Examples:
To enter 146.5200 MHz, press
à
à
à
à
To enter 146.5000 MHz, press
à
à
à
CHANGING THE TRANSMITTER POWER LEVEL
You can select between a total of three transmitter power levels on your VX-150. The
exact power output will vary somewhat, depending on the voltage supplied to the trans-
ceiver. With the standard FNB-64 Battery Pack, the power output levels available are:
HIGH: 5 W MID: 2 W LOW: 0.5 W
To change the power level:
Press the
[
F/W
]
key, then immediately press the
[
3
(
LOW
)]
key.
Now rotate the DIAL knob to select “LOW”, “MID,” or “HIGH”.
Press the PTT key to save the new setting and exit to normal operation.
CHANGING THE CHANNEL STEPS
To change a frequency step, follow the procedure below:
Press the
[
F
]
key, then immediately press the
[
0
(
SET
)]
key to enter the Set mode.
Rotate the DIAL to select Menu Item #6 (“STEP”).
Press the
[
F
]
key to enable modification of the current setting.
Now rotate the DIAL knob to select 5, 10, 12.5, 15, 20, 25 or 50 kHz steps.
Press the PTT key to save the new setting and exit to normal operation.
Basic Operation
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu VX-150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu VX-150 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info