674768
27
Zoom out
Zoom in
Previous page
1/173
Next page
27
Preparation
Preparing the Battery Pack/External Power Supply
Connecting to an External Power Supply Using a Power Cable
(USA/EXP version only)
The optional power cable (E-DC-6) allows the transceiver to be connected to an external
power supply.
1 Turn off the transceiver.
2 Connect the optional external power supply
cable (E-DC-6) to an external power supply.
Remarks Connect the red/black wire or white/red
wire to the positive (+) terminal of the
external power supply and the black wire
to the negative (−) terminal.
Set the voltage of the external power
supply at 12 to 14 V.
3 Insert the plug of the external power supply
into the EXT DC IN jack of the transceiver.
Cautions
y When using the transceiver with the external power supply cable (E-DC-6) connected to an external
power supply, pay attention to the following:
The power supply voltage must be between 12 V and 14 V.
If the voltage exceeds 16 V, malfunctions and damage to the electric circuits of the transceiver may
result. Take extra care.
Connect the red/black wire or white/black wire of the external power supply cable (E-DC-6) to the
positive (+) terminal of the external power supply and the black wire to the negative (−) terminal.
Use an external power supply having sufficient current capacity (3 A or more).
If the transceiver is used with the supplied antenna connected, the transmit RF may interfere with
the external power supply, resulting in malfunction or failure. When using an external power supply,
remove the supplied antenna and connect an external antenna. Place the external power supply
sufficiently away from the transceiver to avoid RF interference.
y Use the transceiver at the minimum required transmission power level to prevent overheating.
y Do not continue transmitting for a prolonged period. The transceiver may overheat, resulting in
malfunction or a burn injury.
y To operate the transceiver for 7 hours or longer, it is recommended that the battery pack be replaced
with the optional battery case (FBA-39).
y Recharging the fully-charged battery pack repeatedly can shorten its service life. Be extremely careful
not to continually recharge the battery when operating the transceiver using an external power supply.
y While charging the battery pack, protect the transceiver from water.
y Charge the battery pack in a place where the ambient temperature is +5 °C to +35 °C (+41 °F to +95
°F).
y If the terminals or electrodes of the battery pack are dirty, the transceiver may malfunction due to poor
contact, resulting in overheating or rupture. If the terminals or electrodes get dirty, clean them using
a dry cloth or cotton swab.
Connect the external
antenna.
External power supply
External power supply
cable E-DC-6
(optional)
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT2DR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT2DR in the language / languages: English as an attachment in your email.

The manual is 40,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info