674767
33
Zoom out
Zoom in
Previous page
1/156
Next page
33
Basic Operation
Listening to the Radio
Listening to the AM/FM Radio
AM broadcast stations can be easily received using “Preset Memory Receiver” (See
page 52), where many major broadcast stations are already saved to this transceiver, or
the stations can be directly tuned in by inputting the frequency of the desired broadcast
station with the O and key pad.
1 Press A
Set A band as the operating band.
2 Press B
Select either the “AM broadcast” or “FM broadcast” bands. The “R” icon will
appear on the display while in the Broadcast Reception mode.
3 Adjust the frequency by turning O or using the key pad (See page 30).
Tip
Broadcast stations that are frequently listened to can be saved to memory (See page 43).
If you would like to scan a radio band, set A band as the operating band and press F, then 2.
If a signal is detected during the scan, a beep will sound; the transceiver will receive the signal for 5
seconds then resume scanning.
The decimal point will flash when the scan is stopped.
Switching between AM Antennas
When listening to AM broadcast stations, the Bar and external antennas may be
switched for best reception according to conditions. During normal use, you may not
need to switch between AM antennas.
Enter the Set mode:
1 Press and hold M for over 1 second.
2 Turn O to select [2 TX/RX].
3 Press H.
4 Turn O to select [1 MODE].
5 Press H.
6 Turn O to select [1 ANTENNA AM].
7 Press H.
8 Turn O to switch to the desired antenna.
Display Operation
BAR & EXT
ANTENNA
AM broadcasts can be received using both
the whip antenna provided at the top of the
transceiver and the built-in bar antenna.
BAR ANTENNA When receiving AM broadcasts, the
transceiver uses only the built-in bar
antenna.
Rotate the transceiver to adjust the AM
broadcast (middle wave band) for the best
receiving sensitivity.
9 Press p to exit from the Set mode.
䎶䎨䎷䎝䎃䎃䎕䎶䎨䎷䎝䎃䎃䎕
䎃䎃䎃䎃䎃䎃䎃
䎃䎃䎃䎃䎃䎃䎃
䎖䫹䎰䎨䎰䎲䎵䎼䎖䫹䎰䎨䎰䎲䎵䎼
䎃䎃䎃䎃䎃䎃䫹䎗䎃䎃䎃䎃䎃䎃䫹䎗 䎱䎪䎱䎪
䎃䎃䎃䎃䎃䎃䎃䎃䎘䎃䎃䎃䎃䎃䎃䎃䎃䎘
䎔䎃䎔䎃 䎰䎲䎧䎨䎰䎲䎧䎨
䎷䎤䎯䎷䎤䎯
䎔䎃䎔䎃 䎤䎱䎷䎨䎱䎱䎤䎃䎃䎤䎰䎤䎱䎷䎨䎱䎱䎤䎃䎃䎤䎰
䎤䎱䎷䎨䎱䎱䎤䎃䎃䎤䎷䎷䎤䎱䎷䎨䎱䎱䎤䎃䎃䎤䎷䎷
䎯䎃䎯䎃䎃䎧
䎗䎃
䎗䎃
䎩䎃 䎲䎱䎲䎱
䎤䎱䎷䎨䎱䎱䎤䎤䎱䎷䎨䎱䎱䎤
䎥䎤䎵䎥䎤䎵 䎨䎻䎷䎨䎻䎷
FT1DR_DE_Eng.indb 33FT1DR_DE_Eng.indb 33 13/06/28 15:1613/06/28 15:16
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT1DR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT1DR in the language / languages: English as an attachment in your email.

The manual is 6,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info