674745
15
Zoom out
Zoom in
Previous page
1/154
Next page
Page 13F
T-991
OperaTing Manual
beFOre YOu begin
connection oF AntennA And poWer cAbleS
Please follow the outline in the illustration regarding the proper connection of antenna coaxial cables, as well as the DC
power cable. The DC power connector for the
FT-991A
must only be connected to a DC source providing 13.8 Volts DC
(
±15 %
)
, and capable of at least 23 Amperes of current. Always observe proper polarity when making DC connection:
The RED DC power lead connects to the Positive
(
+
)
DC terminal.
The BLACK DC power lead connects to the Negative
(
)
DC terminal.
We recommend the use of the
FP-1030A
(
USA market only
)
AC Power Supply. Other models of power supplies may
be used with the
FT-991A
, but the 13.8 VDC input voltage, 23 Ampere current capability, and DC cable polarity guide-
lines described above must be strictly followed.
Note that other manufacturers may use the same type of DC power connections as the
FT-991A
transceiver; however,
the wiring configuration may be different from that specified for the
FT-991A
transceiver. Serious damage can be
caused if improper DC connections are made; consult with a qualied service technician when in doubt.
High RF voltage is present in the TX RF section of the transceiver while transmitting.
Absolutely! Do not touch the TX RF section while transmitting.
Permanent damage can result when improper supply voltage, or reverse-polarity voltage, is applied to the
FT-
991A
. The Limited Warranty on this transceiver does not cover damage caused by application of AC voltage, re-
verse polarity DC, or DC voltage outside the specied range of 13.8 V ±15 %. When replacing fuses, be certain
to use a fuse of the proper rating. The
FT-991A
requires a 25 Amp blade fuse.
note:
Do not place the
FT-991A
in a location with direct exposure to sunshine.
Do not place the
FT-991A
in a location exposed to dust and/or high humidity.
Ensure adequate ventilation around the
FT-991A
, to prevent heat build-up and possible reduction of performance
due to high heat.
Do not install the
FT-991A
on an unstable desk or table. Do not place it in a location where objects may fall onto it
from above.
To minimize the possibility of interference to home entertainment devices, take all precautionary steps including
separation of TV/FM antennas from Amateur transmitting antennas to the greatest extent possible, and keep trans-
mitting coaxial cables separated from cables connected to home entertainment devices.
Ensure that the DC power cord is not subject to undue stress or bending, which could damage the cable or cause it to
be accidentally unplugged from the rear panel
DC IN
jack.
Be certain to install your transmitting antenna
(
s
)
so they cannot possibly come in contact with TV/FM radio or other
antennas, or with power or telephone lines.
Check the DC volt-
age and current
rating
(
+13.8 V, 23 A
)
of the
power supply before con-
necting to the transceiver.
To prevent damage from lightning, at-
mospheric electricity, electrical shock
etc., please provide a good earth ground.
Use a short, thick, braided cable to connect your
station equipment to the
buried ground rod
(
or
alternative earth ground
system
)
.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-991A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-991A in the language / languages: English as an attachment in your email.

The manual is 36,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info