478504
101
Zoom out
Zoom in
Previous page
1/132
Next page
Page 99FT-950 OPERATING MANUAL
To limit scanning (and manual tuning) within a particular frequency range, you can use the Programmable Memory Scan-
ning (PMS) feature, which utilizes nine special-purpose memory pairs (“P1L/P1U” through “P9L/P9U”). The PMS fea-
ture is especially useful in helping you to observe any operating sub-band limits, which apply to your Amateur license class.
1. Store the Lower and Upper tuning/scanning limit fre-
quencies into the memory pair “P1L” and “P1U”, re-
spectively, or any other “L/U” pair of memories in the
special PMS memory area. See page 92 for details re-
garding memory storage.
2. Press the
[
V/M
]
button to enter the “Memory” mode.
ADVICE:
If you can not enter the “Memory” mode, check to see
if the transceiver is in VFO-B mode (the green
[
VFO-
B
(
RX
)]
Indicator/Switch is illuminated). If so, press
the
[
VFO-A
(
RX
)]
Indicator/Switch to return operation
to VFO-A. Now, press the
[
V/M
]
button to enter the
“Memory” mode.
3. Press the
[
MCH
]
button momentarily. The imbedded
LED inside the switch will glow orange.
4. Rotate the
[
CLAR/VFO-B
]
knob to select memory
channel “P1L” or “P1U”.
5. Rotate the
[
SQL
]
knob so that the background noise is
just silenced.
6. Turn the Main Tuning Dial knob slightly (to activate
memory tuning). Tuning and scanning are now limited
to the range within the P1L/P1U limits until you press
the
[
V/M
]
button to return to memory channel or VFO
operation.
7. Press and hold in the microphone’s
[
UP
]
or
[
DWN
]
key for one second to start scanning in the specified
direction.
ADVICE:
If the scanner halts on an incoming signal, the deci-
mal point between the “MHz” and “kHz” digits of
the frequency display will blink.
If the incoming signal disappears, scanning will re-
sume in about five seconds.
On the SSB/CW and SSB-based Data modes, the
scanner will pause on a received signal, then will
step across the signal very slowly, giving you time
to stop the scan, if you like. However, in these
modes on the VFO, the scanner does not stop.
If the scan has paused on a signal, pressing the
microphone’s
[
UP
]
or
[
DWN
]
key will cause scan-
ning to resume instantly.
8. If you rotate the Main Tuning Dial knob in the oppo-
site direction from the current scanning direction (in
other words, you rotate the dial to the left when scan-
ning toward a higher frequency), the direction of the
scan will reverse.
9. If you press the microphone’s PTT switch during scan-
ning, the scanner will halt at once. Pressing the PTT
switch during scanning will not cause transmission.
PMS
(
PROGRAMMABLE MEMORY SCANNING
)
[
SQL
]
Knob
[
VFO-B
(
RX
)]
Button
[
VFO-A
(
RX
)]
Button
[
MCH
]
Button
[
CLAR/VFO-B
]
Knob
Main Tuning Dial Knob
[
V/M
]
Button
101


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-950 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-950 in the language / languages: English as an attachment in your email.

The manual is 6,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info