478504

Yaesu FT-950 Manual

51
Zoom out
Zoom in
Previous page
1/132
Next page
Page 49FT-950 OPERATING MANUAL
INTERFERENCE REJECTION
WIDTH
(
IF DSP BANDWIDTH
)
TUNING
(
SSB/CW/RTTY/PKT MODES
)
The IF WIDTH tuning system allows you to vary the width of the DSP IF passband, to reduce or eliminate interference.
Moreover, the bandwidth may actually be expanded from its default setting, should you wish to enhance incoming signal
fidelity when interference on the band is low.
1. Press the
[
WIDTH
]
button. The LED inside the
[
WIDTH
]
button glows orange. The
[
SELECT
]
knob
functions as the WITDH knob. The current bandwidth
appears in the WIDTH indicator on the display.
2. Rotate the
[
SELECT
]
knob to
the left or right to reduce the in-
terference.
ADVICE:
The frequency display will show
the bandwidth of the IF pass-
band for 3 seconds whenever the
[
SELECT
]
knob is turned.
3. Press the
[
CLEAR
]
button to set
the bandwidth to default.
Using IF SHIFT and WIDTH Together
The IF SHIFT and Variable IF WIDTH features
together form a very effective interference-fight-
ing filtering system.
For example, in Figure “A”, you can see how inter-
ference has appeared both on the high and low sides
of the desired signal. Press the
[
WIDTH
]
button
then rotate the
[
SELECT
(
WIDTH
)]
knob, the in-
terference from one side can be eliminated (Figure
“B”). Next, press the
[
SHIFT
]
button and rotate
the
[
SELECT
(
SHIFT
)]
knob to re-positioning the
passband (Figure “C”), the interference on the op-
posite side can be removed, without re-introduc-
ing the interference previously eliminated in Fig-
ure “B”.
The default bandwidths, and total bandwidth ad-
justment range, will vary according to the operat-
ing mode:
SSB Mode: 1.8 kHz ~ 3.0 kHz (default: 2.4 kHz).
CW Mode: 500 Hz ~ 2.4 kHz (default: 2.4 kHz)
RTTY/PKT Modes: 500 Hz ~ 2.4 kHz (default:
500 Hz)
[
WIDTH
]
Button
[
SELECT
]
Knob
WIDTH Indicator
[
CLEAR
]
Button
ABC
ADVICE:
The IF Bandwidth will be memorized independently on
each VFO stack of VFO-A and VFO-B.
Referring to Figure “B”, you can see the default
bandwidth on the SSB mode by pressing the
[
CLEAR
]
button.
By rotating the
[
SELECT
(
WIDTH
)]
knob to the
left, the bandwidth will narrow (see Figure “A”,
while rotation of the
[
SELECT
(
WIDTH
)]
knob to
the right, as depicted in Figure “C”, will increase
the bandwidth.
ADVICE:
For best interference reduction, the WIDTH and
SHIFT features are the primary tools you should
use. After narrowing the bandwidth (WIDTH) and/
or adjusting the center of the passband (SHIFT).
The Contour control may then yield additional sig-
nal-enhancement benefits on the net residual band-
width. Even more, the IF NOTCH Filter (described
later) may also be used, in conjunction with these
filter systems, to significant advantage.
ABC
IF
BANDWIDTH
IF
BANDWIDTH
IF
BANDWIDTH
Desired Signal Desired Signal Desired Signal
QRM
QRMQRMQRM
QRMQRM
IF
BANDWIDTH
IF
BANDWIDTH
IF
BANDWIDTH
… 51 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-950 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-950 in the language / languages: English as an attachment in your email.

The manual is 6,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info