478500
26
Zoom out
Zoom in
Previous page
1/76
Next page
Page 24 FT-897D OPERATING MANUAL
LOCKING FRONT PANEL CONTROLS
The front panel LOCK button allows you to disable the DIAL
and/or the front panel controls.
RECEIVER ACCESSORIES
BATT- A
BATT- B
BAND
MODE
CLARAF
LOCK
PHONE
MIC
SQL
/RF
MEM/VFO CH
DWN UP
V/M
DSP
UP
DSP
F
LOCK
In the transceivers default configuration, pressing the LOCK
button disables just the DIAL, while the other keys and
switches are unaffected.
To lock out the remainder of the controls and the MEM/
VFO CH knob, use Menu Mode No-054
[
LOCK MODE
]
;
1. Press and hold in the
[
F
]
key for one second to enter the
Menu mode.
2. Rotate the MEM/VFO CH knob so as to recall No-054
[
LOCK MODE
]
.
3. Rotate the DIAL to select the desired configuration:
DIAL: Locks DIAL knob only.
FREQ: Locks front panel keys and knobs related to fre-
quency control (such as BAND
(
DWN
)
and
BAND
(
UP
)
key,
[
A
](
A/B
)
key., etc.)
PANEL: Locks all front panel keys and knobs (except
POWER and LOCK keys)
ALL: Locks all front panel keys and knobs (except
POWER and LOCK keys) and microphone
keys.
4. When you have made your selection, Press and hold in
the
[
F
]
key for one second to save the new setting and
exit to normal operation.
When the controls are locked out, press the LOCK button
once more to release them to normal operation.
CLARIFIER
(
RECEIVER INCREMENTAL TUNING
)
The Clarifier (RIT) allows you to set an offset of up to ±9.99
kHz of the receive frequency relative to your transmit fre-
quency. To achieve a wider offset than this, you may use the
“Split” operating mode, described later.
1. Press the CLAR/IF SHIFT button momentarily to acti-
vate the Clarifier function.
2. Turn the CLAR knob, which allows the receiver fre-
quency to be varied over a range of ±9.99 kHz.
3. When the receiving frequency is
higher than transmit frequency, the
(within 1 kHz)” or “ (exceed 1
kHz)” icon will appear at the right
of the frequency display. Similarly,
when the receiving frequency is
lower than transmit frequency, the
(within 1 kHz)” or “ (exceed 1
kHz)” icon will appear at the right
of the frequency display. When the
receiving frequency is equal to trans-
mit frequency (Clarifier offset is
zero) while the Clarifier is activated,
the “” icon will appear at the right
of the frequency display.
4. To turn the Clarifier off, again press
the CLAR/IF SHIFT button mo-
mentarily. When you turn the Clari-
fier back on, the offset previously
stored will still be applied.
5. To reset the Clarifier offset to zero, turn the Clarifier off,
then turn the DIAL by any amount. The Clarifier will
reset to zero after the first “step” of the DIAL.
1) If you leave the Clarifier on, moving the DIAL
will not cause the offset to be cancelled.
2) You may change the knob that controls the
Clarifier offset from the DIAL to the MEM/VFO
CH knob via Menu Mode No-021
[
CLAR DIAL SEL
]
.
[
TX<RX
(
within 1 kHz
)]
[
TX=RX
(
Simplex
)]
[
TX>RX
(
within 1 kHz
)]
[
TX>RX
(
exceed 1 kHz
)]
BATT- A
BATT- B
BAND
MODE
CLARAF
LOCK
PHONE
MIC
SQL
/RF
MEM/VFO CH
DWN UP
V/M
DSP
UP
DSP
F
CLARCLAR/IF SHIFT
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-897D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-897D in the language / languages: English as an attachment in your email.

The manual is 3,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info