36023

Yaesu ft-897D Manual

54
Zoom out
Zoom in
Previous page
1/76
Next page
Page 52 FT-897D OPERATING MANUAL
BEACON FEATURE
The FT-897D’s unique “Beacon” feature allow you to set up the transceiver to send a repetitive message. For example, on a
DX-pedition, the FT-897D beacon might be activated on a 50 MHz frequency, to alert DXers as to possible band openings.
MISCELLANEOUS SETTINGS
Beacon Transmission (On the Air)
1. Press and hold in the
[
F
]
key for one second to enter the
Menu mode.
2. Rotate the MEM/VFO CH knob to select Menu Mode
No-012
[
BEACON TIME
]
.
3. Rotate the DIAL to select the interval time (between mes-
sage and message) (1 ~ 255 seconds).
4. Press and hold in the
[
F
]
key for one second to exit to
normal operation.
5. Press the
[
F
]
key momentarily, then rotate the MEM/
VFO CH knob, as needed, until Multi Function Row
“o”
[
PLY1, PLY2, PLY3
]
appears on the display.
6. Press the
[
A
](
PLY1
)
key to activate the Beacon Feature.
NOTE: When using the “beacon” feature, please disable the
“VOX” feature.
If you press
[
B
](
PLY2
)
or
[
C
](
PLY3
)
, the mes-
sage will be transmitted, after which the trans-
mission will halt. Operationally, these two keys
function the same as a traditional CW message keyer.
7. To disable the transmission from the Beacon, just repeat
the above procedure, rotating the DIAL to select “OFF”
in step 3 above.
You may adjust the CW speed using Menu Mode
No-030 [CW SPEED].
You may also send the Beacon Text manually. If this is done,
all three “Beacon” messages may be used as a traditional
CW message keyer. To do this:
1. Press and hold in the
[
F
]
key for one second to enter the
Menu mode.
2. Rotate the MEM/VFO CH knob to select Menu Mode
No-012
[
BEACON TIME
]
.
3. Rotate the DIAL to select “OFF.”
4. Press and hold in the
[
F
]
key for one second to exit to
normal operation.
5. Press the
[
F
]
key momentarily, then rotate the MEM/
VFO CH knob, as needed, until Multi Function Row
“o”[PLY1, PLY2, PLY3] appears on the display.
6. Press the
[
A
](
PLY1
)
key momentarily to send the “BEA-
CON TEXT 1” message.
Alternatively, pressing the
[
B
](
PLY2
)
or
[
C
](
PLY3
)
key
will initiate the message at those respective break points.
Beacon Text Storage
1. Press and hold in the
[
F
]
key for one second to enter the
Menu mode.
2. Rotate the MEM/VFO CH knob to select Menu Mode
No-011
[
BEACON TEXT 1
]
.
3. Press the MEM/VFO CH knob to enable storage of the
Beacon Text (the first character location will be underlined).
4. Rotate the DIAL to select the first character (number or
letter) in the Beacon Text you wish to store, then rotate
the MEM/VFO CH knob one click clockwise to move
to the next character.
5. Repeat step 4 as many times as necessary to complete
the Beacon Text.
❒If the Beacon Text is less than 40 characters long,
add the “ ” mark after the last character to terminate
the text, then press the MEM/VFO CH knob.
❒If the Beacon Text is more than 40 characters long,
but less than 79, set the last (40th) character to be
“ ,” press the MEM/VFO CH knob, then rotate the
to select “BEACON TEXT 2.” Now repeat step 4.
❒If the Beacon Text is more than 79 characters long,
up to 118 characters may be stored. In this case, set
the final character slot in “BEACON TEXT 2” to be
“ ,” press the MEM/VFO CH knob, then rotate the
to select “BEACON TEXT 3.” Now repeat step 4.
❒Do not forget to install the “ ” mark after the last
character, to terminate the text.
6. Press and hold in the
[
F
]
key for one second until you
hear a double beep; the second beep confirms that the
Beacon text was successfully stored.
… 54 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu ft-897D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu ft-897D in the language / languages: English as an attachment in your email.

The manual is 3,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info