674739
43
Zoom out
Zoom in
Previous page
1/62
Next page
41FT-891 Operating Manual
Scanning Operation
You may scan either the VFO or the memories of the FT-891, and the radio will halt
scanning on any frequency with a signal strong enough to open the receiver squelch.
VFO Scanning
1. Set VFO-A to the frequency on which you would like to begin scanning.
2. The
[
RF/SQL
]
knob may be changed
from the “RF” Function to the “SQL” Function
via Menu mode “05-05
[
RF/SQL VR
]
”.
3. Rotate the
[
RF/SQL
]
knob so that the back-
ground noise is just silenced.
4. Press and hold in the microphone
[
UP
]
or
[
DWN
]
key for one second to start scanning
in the specified direction on the VFO fre-
quency.
NOTE: Set the “Microphone Automatic
Scanning” function to ON or OFF via
Menu Mode “05-15
[
MIC SCAN
]
”.
5. If the scanner halts on an incoming signal,
the decimal point between the “MHz” and
“kHz” digits of the frequency display will
blink.
DWN UP
PTT
r If the incoming signal disappears, scanning will resume in about five seconds.
r If the scan has paused on a signal, pressing the microphone
[
UP
]
or
[
DWN
]
key, will
cause scanning to resume instantly.
r If the Main Tuning DIAL knob is rotated while scanning is in progress, the scanning
will continue up or down in frequency according to the direction of the DIAL Knob
rotation.
(
in other words, if the dial is rotated to the left when scanning toward a
higher frequency, the direction of the scan will reverse.
)
r On the SSB/CW and SSB-based Data modes, the scanner will pause on a received
signal, then will step across the signal very slowly, giving you time to stop the scan,
if you like. However, In these modes on the VFO, the scanner does not stop.
6. To cancel scanning, press the PTT switch.
r If you press the microphone PTT switch during scanning, the scanner will halt at
once. However, pressing the PTT switch during scanning will not cause transmis-
sion.
Scan Resume Options
The manner in which the scanner resumes after it has paused on a signal may be selected
by using Menu mode
05-16
[
MIC SCAN RESUME
]
”.
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-891 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-891 in the language / languages: English as an attachment in your email.

The manual is 20,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info