478498

Yaesu FT-817ND Manual

73
Zoom out
Zoom in
Previous page
1/84
Next page
71FT-817ND Operating Manual
CAT SYSTEM PROGRAMMING
CAT Data Protocol
All commands sent from the computer to the transceiver consist of five-byte blocks, with
up to 200 ms between each byte. The last byte in each block is the instruction opcode, while
the first four bytes of each block are arguments (either parameters for that instruction, or
dummy values required to pad the block out to five bytes). Each byte consists of 1 start bit,
8 data bits, no parity bit, and two stop bits.
There are 17 instruction opcodes for the FT-817ND, listed in the chart on next page. Many
of these opcodes are On/Off toggle commands for the same action (e.g. “PTT On” and
“PTT Off.” Most of these commands require some parameter or parameters to be set. Irre-
spective of the number of parameters present, every Command Block sent must consist of
five bytes.
Accordingly, any CAT control program must construct the five-byte block by selecting
the appropriate instruction opcode, organizing the parameters as needed, and providing
unused “dummy” Eargument bytes to pad the block to its required five-byte length (the
dummy bytes can contain any value). The resulting five bytes are then sent, opcode last,
from the computer to the FT-817ND CPU via the computer’s serial port and the transceiver’s
ACC jack.
All CAT data values are hexadecimal.
Constructing and Sending CAT Commands
Example #1: Set the VFO frequency to 439.70 MHz
Per the CAT command table, the opcode for “Set Frequency” is 01. Placing the opcode
into the 5th data bit position, we then enter the frequency into the first four data bit
positions:
DATA 1 DATA 2 DATA 3 DATA 4 DATA 5
43 97 00 00 01
Parameter Command
Send these five bytes to the transceiver, in the order shown above.
Example #2: Turn the Split Mode “On”
Per the CAT command table, the opcode for “Split On/off” is 02. Placing the opcode
into the 5th data bit position, we then enter dummy values into all other parameter
locations:
DATA 1 DATA 2 DATA 3 DATA 4 DATA 5
00 00 00 00 02
Dummy Data Command
CAT DATA BYTE FORMAT
CAT 5-BYTE COMMAND STRUCTURE
… 73 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-817ND at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-817ND in the language / languages: English as an attachment in your email.

The manual is 3,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info