478466
66
Zoom out
Zoom in
Previous page
1/84
Next page
64 FT-7900R OPERATING MANUAL
MISCELLANEOUS SETTINGS
DCS CODE INVERSION
The DCS system was first introduced in the commercial LMR (Land Mobile Radio) service,
where it is now in widespread use. DCS is sometime referred to by its different proprietary
names, such as DPL
®
(Digital Private Line
®
, a registered trademark of Motorola, Inc.).
DCS uses a codeword consisting of a 23-bit frame, transmitted (subaudible) at a data rate of
134.4 bps (bit/sec). Occasionally, signal inversion can result in the complement of a code to
be sent or received. This prevents the receivers squelch from opening with DCS enabled, as
the decoded bit sequence would not match that selected for operation.
Typical situations that might cause inversion to occur are:
Connection of an external receiver preamplifier.
Operating through a repeater.
Connection of an external linear amplifier.
Note that code inversion does not mean that any of the above listed equipment is defective!
In certain amplifier configurations, the output signal (phase) is inverted from the input.
Small signal or power amplifiers having an odd number (1, 3, 5, etc.) of amplification stages
may result in inversion of a transmitted or received DCS code.
While under most circumstances this should not occur (amplifier designs and industry stan-
dards take this into account), if you find that your receiver squelch does not open when both
you and the other station are using a common DCS code, you or the other station (but not
both) can try the following:
1. Press and hold in the
[
BAND
(
SET
)]
key for 1/2 second to enter the Set mode.
2. Rotate the DIAL knob to select Menu #10 (
DCS.NDCS.N
DCS.NDCS.N
DCS.N/
RR
RR
R).
3. Press the
[
BAND
(
SET
)]
key momentarily, then rotate
the DIAL knob to select the following mode.
TT
TT
T/
RX NRX N
RX NRX N
RX N: Encoder; Normal, Decoder; Normal
RX RRX R
RX RRX R
RX R: Encoder; Normal, Decoder; Reverse (Inverted)
TX RTX R
TX RTX R
TX R: Encoder; Reverse (Inverted), Decoder; Normal
TT
TT
T/
RX RRX R
RX RRX R
RX R: Encoder; Reverse (Inverted), Decoder; Reverse (Inverted)
4. Press the
[
BAND
(
SET
)]
key momentarily to save the new setting, then press and hold in
the
[
BAND
(
SET
)]
key for 1/2 second to exit to normal operation.
Remember to restore the default setting to “
TT
TT
T/
RX NRX N
RX NRX N
RX N” (Encoder; Normal, Decoder; Normal)
when done.
66


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-7900R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-7900R in the language / languages: English as an attachment in your email.

The manual is 2,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info