478466
54
Zoom out
Zoom in
Previous page
1/84
Next page
52 FT-7900R OPERATING MANUAL
The ARTS feature uses DCS signaling to inform both parties when you and another ARTS-
equipped station are within communications range. This may be particularly useful during
Search-and Rescue situations, where is important to stay in contact with other members of
your group.
Both stations must set up their DCS codes to the same code number, then activate their
ARTS feature using the command appropriate for their radio. Alert ringers may be activated,
if desired.
Whenever you push the PTT switch, or every 25 seconds
after ARTS is activated, your radio will transmit a signal
which includes a (subaudible) DCS signal for about one
second. If the other radio is in range, the beeper will sound
(if enabled) and the display will show “
IN.RNGIN.RNG
IN.RNGIN.RNG
IN.RNG” as opposed
to the out of range display “
OUT.RNGOUT.RNG
OUT.RNGOUT.RNG
OUT.RNG” in which ARTS op-
eration begins.
Whether you talk or not, the polling every 25 seconds will continue until you de-activate
ARTS. Every 10 minutes, moreover, you can have your radio transmit your callsign via CW,
so as to comply with identification requirements. When ARTS is de-activated, DCS will also
be deactivated (if you were not using it previously in non-ARTS operation).
If you move out of range for more than one minute (two pollings), your radio will sense that
no signal has been received, three beeps will sound, and the display will revert to “
OUT.RNGOUT.RNG
OUT.RNGOUT.RNG
OUT.RNG”.
If you move back into range, your radio will again beep, and the display will change back to
the “
IN.RNGIN.RNG
IN.RNGIN.RNG
IN.RNG” indication.
During ARTS operation, it is not possible to change the operating frequency or other set-
tings; you must terminate ARTS in order to resume normal operation. This is a safety feature
designed to prevent accidental loss of contact due to channel change, etc. Here is how to
activate ARTS:
Basic ARTS Setup and Operation
1. Set your radio and the other radio(s) to the same DCS code number, per the discussion
on page 29.
2. Press and hold in the
[
S.SCH
(
ARTS
)]
key for 1/2 sec-
ond. You will observe the “
OUT. RNGOUT. RNG
OUT. RNGOUT. RNG
OUT. RNG” display on the
LCD. ARTS operation has now commenced.
3. Every 25 seconds, your radio will transmit a “polling” call to the other station. When that
station responds with its own ARTS polling signal, the
display will change to “
IN.RNGIN.RNG
IN.RNGIN.RNG
IN.RNG” to confirm that the other
station’s polling code was received in response to yours.
4. Press and hold in the
[
S.SCH
(
ARTS
)]
key for 1/2 second to exit ARTS operation and
resume normal operation of the transceiver.
ARTS
: AUTO RANGE TRANSPONDER SYSTEM
54


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-7900R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-7900R in the language / languages: English as an attachment in your email.

The manual is 2,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info