674725
18
Zoom out
Zoom in
Previous page
1/47
Next page
18
FT-70DR/DE Advance Manual
Scanning Only the Specified Memory Channels
1. Recall the memory channel registered as a specified memory channel.
2. Press the
[
F
]
key, then press the
[
2
]
(SCAN) key to start scanning.
Only the memory channels registered as the specified memory channels are
scanned.
Unless two or more specified memory channels are registered, the specified memory channel
scanning does not function.
Programmable Memory Channel Scan (PMS)
Registering to the Programmable Memory Channels
50 sets of PMS memory channels (L1/U1 to L50/U50) are available.
Register the lower and upper frequencies of the frequency range in a pair of Program-
mable Memory Channels,
L
££
: Lower limit memory channel
U
££
: Upper limit memory channel
For more details on registering frequencies to the memory channel, see “Registering To
Memory channel” (see the operating manual).
z
Make sure to use the corresponding numbers for the lower and upper limit memory channels.
z
Set the PMS memory channel for performing the Programmable Memory scanning (PMS) as
follows.
The scan width of the upper and lower limit frequencies must be 100 kHz or more.
The lower and upper limit memory channels must be within the same frequency band.
The lower and upper limit memory channels must not register the lower and upper
channels in reverse.
The PMS memory channel must not register a skip memory channel.
Performing Programmable Memory Channel Scan
The programmable memory channel scan allows scanning a specified frequency range
within the same frequency band.
1. Recall the PMS memory channel to which the lower limit (L
££
)
or upper limit (U
££
)
of the frequency is registered.
2. Press the
[
F
]
key, then press the
[
2
]
(SCAN) key.
Programmable memory channel scanning starts.
During scanning, “P
££
” appears on the upper left side of the LCD.
If the DIAL knob is rotated while scanning is in progress, the scanning will contin-
ue up or down in frequency according to the direction of the DIAL Knob rotation.
If the scanner halts on an incoming signal, the back light will turn ON and the dec-
imal point between the “MHz” and “kHz” digits of the frequency display will blink.
Scanning will resume in about five seconds.
3. Press the PTT switch to cancel the scanning.
z
If the scan has paused on a signal, rotating the DIAL knob will cause scanning to resume
instantly.
z
During scanning, the frequency may be changed only within the programmed frequency
range.
z
During scanning, press the
[
V/M
]
key to return to the normal memory mode.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-70DE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-70DE in the language / languages: English as an attachment in your email.

The manual is 6,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yaesu FT-70DE

Yaesu FT-70DE User Manual - English - 44 pages

Yaesu FT-70DE User Manual - German - 44 pages

Yaesu FT-70DE Additional guide - German - 47 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info