674732
88
Zoom out
Zoom in
Previous page
1/102
Next page
Page 86 FT-450D OPERATION MANUAL
STBY BP (STBY BEEP)
Function: Setting of standby beep
Available Values: OFF / ON
Default: OFF
OFF: No beep sound is transmitted.
ON: A beep is transmitted before returning to
receive.
The beep, transmitted when the PTT is released, will
inform the other operators that your transmission has
ended.
TONE F (TONE FREQ)
Function: Sets the CTCSS Tone Frequency.
Available Values: 67.0 ~ 254.1 (Hz)
50 Standard CTCSS tones
Default: 88.5 (Hz)
TOT (TOT TIME)
Function: Selects the time of the Time-Out-Timer.
Available Values: OFF/1 ~ 20 (min)
Default: OFF
MENU MODE
TUNER (TUNER/ATAS)
Function: Setting of the Auto Antenna and Antenna
Tuner
Available Values: ATAS / EXT ATU / INT ATU
/ INTRATU / F RANS
Default: INT ATU
Selects the device (FC-40 or ATAS-100/-120/-120A)
controlled by the front panel’s
[
TUNE
]
button.
ATAS: The
[
TUNE
]
button will activate the op-
tional ATAS-100/-120/-120A on the HF
amateur bands and 50 MHz amateur
band.
EXT ATU: The
[
TUNE
]
button will activate the op-
tional FC-40.
INT ATU: The
[
TUNE
]
button will activate the An-
tenna Tuner. The tuner passes only the
Transmitter RF.
INTRATU: The
[
TUNE
]
button will activate the An-
tenna Tuner. The tuner passes both the
Transmitter RF and the Receiver signal.
F TRANS: The frequency data of the radio is sent to
another FT-450D. This feature is very
usefll for the “SO2R” (Single Operator,
Two Radio) operation. In this case, the in-
terconnection is as follows.
INPUT
DC 13.8V
22A
ANT
GND
EXT
SPKR
CATLINEARTUNERDATA
INPUT
DC 13.8V
22A
ANT
GND
EXT
SPKR
CATLINEARTUNERDATA
T
U
N
E
R
C
A
T
Junction Connector
Dsub 9pin to Dsub 9pin
Cross CableCT-62
MASTER SETTING
Set menu itme “TUNER” to “F TRANS”.
SLAVE TRANSCEIVER SETTING
Set menu itme “CAT RTS” to “DISABLE”.
Set menu itme “CATRATE” to “4800 bps”.
OPERA TION
When the
[
TUNE
]
button on the Master Transceiver is pressed, the
Slave Transceiver frequency becomes the same as the Master Trans-
ceiver.
IMPORTANT NOTICE
Please install an antenna protection circuit so the Master (RX) Trans-
ceiver is not damaged when the Slave (TX) Transceiver is transmitting.
88


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-450D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-450D in the language / languages: English as an attachment in your email.

The manual is 7,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info