674732
48
Zoom out
Zoom in
Previous page
1/102
Next page
Page 46 FT-450D OPERATION MANUAL
The powerful CW operating capabilities of the FT-450D include operation using both an electronic keyer paddle
and a “straight key” or emulation thereof, as is provided by a computer-based keying device.
SETUP FOR STRAIGHT KEY
(
AND STRAIGHT KEY EMULATION
)
O
PERATION
Before starting, connect your key to the front panel KEY jack in the status that turned off the
[
POWER
(
ON/OFF
)]
switch, and be sure the
[
KEYER
]
button is turned off (the “ ” icon is not displayed) for now.
1. Press the
[
BAND
]
/
[
BAND
]
buttons to select
the operating band.
By pressing the
[
BAND
]
/
[
BAND
]
buttons, the
operating band will change as follows.
7 10 14 15 18 21 24.5
28 50 1.8 3.5 7
......
2. Press the
[
MODE
]
/
[
MODE
]
buttons to select
the CW mode.
3. Rotate the
[
MAIN DIAL
]
knob to adjust the oper-
ating frequency.
If you use the MH-31A8J (or MD-100A8X: option),
you may adjust the operating frequency by the
[
UP
]
/
[
DWN
]
buttons on the microphone.
4. Press the
[
F
]
button followed by the
[
STO/VOX
]
button to engage automatic activation of the trans-
mitter when you close the CW key. The “
icon will appear in the display.
5. When you close your CW key, the transmitter will
automatically be activated, and the CW carrier
will be transmitted. When your release the key,
transmission will cease after a brief delay. The
delay time is user-programmable, per the discus-
sion on page 48.
NOTE:
Do not use the plug except the 3.5-mm 3-pin type
plug. If the plug in correct size is not used the
radio may be harmed or damaged.
CW MODE OPERATION
[
F
]
button
[
MAIN DIAL
]
knob
[
KEYER
]
button
[
BAND
]
/
[
BAND
]
button
[
MODE
]
/
[
MODE
]
button
[
STO/VOX
]
button
NOTICE
Regarding of the
[
DSP/SEL
]
knob
The
[
DSP/SEL
]
knob is used for operating
various functions depending on the situation.
If you can not change the frequency/memory
channel by tuning the
[
DSP/SEL
]
knob, the
[
DSP/SEL
]
knob is selected to operate of one
of the DSP functions.
In this case, press the
[
DSP
]
button several
times until the “>” icon disappears from the
DSP Graphic Display.
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-450D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-450D in the language / languages: English as an attachment in your email.

The manual is 7,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info