674732
4
Zoom out
Zoom in
Previous page
1/102
Next page
Page 2 FT-450D OPERATION MANUAL
PHONES
KEY
F
RONT
P
ANEL
B
UTTONS
AND
K
NOBS
PHONE Jack
A 3.5 mm, 3-contact jack accepts ei-
ther monaural or stereo headphones
with 2 or 3-contact plugs. When a plug
is inserted, the loudspeaker is dis-
abled.
N
OTE:
When wearing headphones, we rec-
ommend that you turn the AF GAIN
levels down to their lowest settings
before turning power on, to minimize
the impact on your hearing caused by
audio “pops” during switch-on.
KEY Jack
This 3.5 mm, 3-contact
jack accepts a CW key or
keyer paddles (for the
built-in electronic keyer),
or output from an external
electronic keyer. Pinout is
shown below. Key up is 5
volts, and key down cur-
rent is 0.5 mA.
DSP Button
This button selects the DSP functions.
Available selections are CONTOUR,
NOTCH, DNR, and WIDTH.
IPO/ATT Button
This button selects the IPO or ATT feature. Available se-
lections are:
ATT:OFF/IPO:OFF ATT:OFF/IPO:ON
ATT:ON/IPO:OFF ATT:ON/IPO:ON
ATT:OFF/IPO:OFF
IPO: OFF, ATT: OFF
Attenuator is OFF, and the RF preamplifier amplifies
the incoming signal.
IPO: ON, ATT: OFF
Attenuator is OFF, and the received signal bypasses
the RF preamplifier, yielding a direct feed to the first
mixer.
IPO: OFF, ATT: ON
The received signal is reduced by 20 dB, and the RF
preamplifier amplifies the incoming signal.
IPO: ON, ATT: ON
The received signal is reduced by 20 dB, and the in-
coming signal bypasses the RF preamplifier, yielding a
direct feed to the first mixer.
The selection will be indicated in the Block Diagram on
the display.
ON/OFF Button
Press and hold in this button for one second
to turn the transceiver on or off.
NB Button
This button turns the IF Noise Blanker
on and off. Press this button to re-
duce short-duration pulse noise.
AGC Button
This button selects the AGC characteristics for the receiver.
Press and hold in this button for one second to disable the
AGC (for testing or weak-signal reception).
Do not use the plug except the 3.5-mm 3-pin type plug. If the plug in correct size is
not used the radio may be harmed or damaged.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-450D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-450D in the language / languages: English as an attachment in your email.

The manual is 7,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info