478473

Yaesu FT-270R Manual

33
Zoom out
Zoom in
Previous page
1/88
Next page
FT-270R OPERATING MANUAL 29
MEMORY MODE
The FT-270R provides a wide variety of memory system resources. These include:
200 “Standard” memory channels, numbered “1” through “200.”
A “Home” channel, providing storage and quick recall of one prime frequency.
10 sets of band-edge memories, also known as “Programmable Memory Scan” chan-
nels, labeled “L1/U1” through “L10/U10.”
10 Memory Banks, labeled “BANK 1” through “BANK10.” Each Memory Bank
can be assigned up to 200 channels from the “standard” memory channels.
10 “Weather Broadcast” Channels.
MEMORY STORAGE
1. Select the desired frequency, while operating in the VFO mode. Be sure to set up any
desired CTCSS or DCS tones, as well as any desired repeater offset, now. The power
level may also be set at this time, if you wish to store it.
2. Press and hold in the
[
MR/MW
(
SKIP
)]
key for one second.
3. Within ten seconds of releasing the
[
MR/MW
(
SKIP
)]
key, you need to make a deci-
sion regarding channel storage. The microprocessor will automatically select the next-
available “free” channel (a memory register on which no data has been stored), so you
may not wish to make any change; if this is the case, proceed to step 4. If you wish to
select a different channel number into which to store the data, rotate the DIAL knob to
select the desired memory channel. You may jump 10 memory channels, if you’re in a
hurry (11 21 31 …) by pressing the
[
VFO
(
PRI
)]
key (multiple times, if necessary).
4. Press the
[
MR/MW
(
SKIP
)]
key once more to store the frequency into memory.
5. You still will be operating in the “VFO” mode, so you may now enter other frequencies,
and store them into additional memory locations, by repeating the above process.
Storing Independent Transmit Frequencies (“Odd Splits”)
All memories can store an independent transmit frequency, for operation on repeaters with
non-standard shift. To do this:
1. Store the receive frequency using the method already described under MEMORY
STORAGE (it doesn’t matter if a repeater offset is active).
2. Tune to the desired transmit frequency, then press and hold in the
[
MR/MW
(
SKIP
)]
key for one second.
3. Within ten seconds of releasing the
[
MR/MW
(
SKIP
)]
key, rotate the DIAL knob to
select the same memory channel number as used in step “1” above.
4. Press and hold in the PTT switch. Then while holding the PTT switch in, momentarily
press the
[
MR/MW
(
SKIP
)]
key once more. (This does not key the transmitter).
1) The “Odd Splits” feature permits setting TONE/DCS indi-
vidually for transmit and receive. Briefly, press the [F/L] key,
and then press the [2(CODE)] key. Rotate the DIAL knob to
select the TONE or DCS for receive. You can confirm the Transmit and
receive TONE/DCS by alternately pressing of the [REV(HOME)] key.
r: receiver
t: transmit
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-270R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-270R in the language / languages: English as an attachment in your email.

The manual is 3,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info