478472
34
Zoom out
Zoom in
Previous page
1/44
Next page
FT-250R OPERATING MANUAL30
The FT-250R may be used for Packet operation, using the optional CT-44 microphone
adapter (available from your Yaesu dealer) for easy interconnection to commonly-avail-
able connectors wired to your TNC. You may also build your own cable using a four-
conductor miniature phone plug, per the diagram below.
The audio level from the receiver to
the TNC may be adjusted by using the
VOL knob, as with voice operation.
The input level to the FT-250R from
the TNC should be adjusted at the
TNC side; the optimum input voltage
is approximately 5 mV at 2 k-Ohms.
Be sure to turn the transceiver and
TNC off before connecting the cables,
so as to prevent voltage spikes from
possibly damaging your transceiver.
Also, be certain to turn off the Receiver Battery Saver, if activated (see page 10).
MICROPROCESSOR RESETTING
In the event that erratic, unpredictable transceiver operation is encountered, it is possible
that the microprocessor has sustained a static burst or other condition that has caused
corruption of some of its data. If this should happen, resetting of the microprocessor should
clear up the problem. Here is the procedure for resetting the microprocessor (this will
restore all factory defaults, and will erase all memories):
c
Turn the radio off.
d
Press and hold the PTT and LAMP key while turning the radio on.
e
Rotate the DIAL to select “
ALL.RSTALL.RST
ALL.RSTALL.RST
ALL.RST” on the LCD.
f
Press the
[
F/L
]
key momentarily to initialize the radio.
SET MODE RESETTING
This “Reset” procedure restores the Menu (“Set mode”) settins to their factory defaults,
without affecting your regular memories.
c
Turn the radio off.
d
Press and hold the PTT and LAMP key while turning the radio on.
e
Rotate the DIAL to select “
SET.RSTSET.RST
SET.RSTSET.RST
SET.RST” on the LCD.
f
Press the
[
F/L
]
key momentarily to initialize the Set mode.
Interface of Packet TNCs & Reset
EAR
MIC
SP
GND
MIC
PTT
GND
TNC
2 K
10 μF
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-250R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-250R in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info