Manual Yaesu FT-2000D (page 121 of 140) (English)

478497

121

Zoom out

Zoom in

1/140

Page 119FT-2000D OPERATING MANUAL

034 GEnE TRACK

Function: Sets the VFO Tracking feature.

Available Values: OFF / bAND / FrEq

Default Setting: OFF

OFF: Disables the VFO Tracking feature.

bAND: When you change bands on the Main (VFO-

A) side, the Sub (VFO-B) band’s VFO will

automatically change to be the same as that of

VFO-A.

FrEq: This function is the almost same as “bAND,”

however, furthermore, the Sub band’s (VFO-

B) frequency changes together with the Main

Band’s (VFO-A) frequency when turning the

Main Dial Tuning knob.

035 GEnE TX TOT

Function: Sets the Time-Out Timer countdown time.

Available Values: OFF / 3 / 5 / 10 / 15 / 20 / 30 min

Default Setting: OFF

The Time-Out Timer shuts off the transmitter after con-

tinuous transmission of the programmed time.

036 GEnE TRV SET

Function: Sets the 10’s and 1’s of the MHz digits display

for operation with a transverter.

Available Values: 30 ~ 49 MHz

Default Setting: 44 MHz

The default setting would be used with a 144 MHz

transverter. If you connect a 430 MHz transverter to the

radio, set this menu to “30” (the “100 MHz” digits are

hidden on this radio).

037 GEnE μT DIAL

Function: Selects the μ-TUNE mode.

Available Values: StP1 / StP2 / OFF

Default Setting: StP1

StP1: Activates the μ-TUNE system using

“COARSE” steps of the

[

VRF

]

knob (2 steps/

click) on the 7 MHz and lower amateur bands.

On the 10/14 MHz bands, “FINE”

[

VRF

]

knob

steps (1 step/click) will be used.

StP2: Activates the μ-TUNE system using “FINE”

steps of the

[

VRF

]

knob (1 step/click) on the

14 MHz and lower amateur bands on the Main

band (VFO-A).

OFF: Disables the μ-TUNE system. Activates the

VRF feature on the 14 MHz and lower amateur

bands on the main band (VFO-A).

ADVICE:

If the optional RF μTuning Kit is not connected, this ad-

justment has no effect.

038 GEnE SNB LVL

Function: Adjusts the Sub band (VFO-B) receiver’s IF

Noise Blanker level, when the Noise Blanker is engaged.

Available Values: nAin(MAIN) / 0~100

Default Setting: nAin(MAIN)

When this menu is set to “nAin(MAIN),” you may adjust

the Noise Blanker level using the front panel’s

[

]

knob.

039 GEnE SUB FIL

Function: Defines the Sub band (VFO-B) receiver’s CW

narrow filter.

Available Values: 1200 / 500 / 300 Hz

Default Setting: 1200 Hz

ADVICE:

This Menu item tells the microprocessor which (if any)

optional filter has been installed.

040 GEnE MIC SCN

Function: Enables/disables scanning access via the

microphone’s

[

]

[

DWN

]

keys.

Available Values: On / OFF

Default Setting: On

041 GEnE SCN RSM

Function: Selects the Scan Resume mode.

Available Values: CAr / 5SEc

Default Setting: 5SEc

CAr: The scanner will hold until the signal disappears,

then will resume after one second.

5SEc: The scanner will hold for five seconds, then re-

sume whether or not the other station is still

transmitting.

042 GEnE ANTIVOX

Function: Adjusts the Anti-VOX Trip Gain which is the

level of negative feedback of receiver audio to the micro-

phone, to prevent receiver audio from activating the trans-

mitter (via the microphone) during VOX operation.

Available Values: 0 ~ 100

Default Setting: 50

043 GEnE FRQ ADJ

Function: Adjusts the reference oscillator.

Available Values: –25 ~ 0 ~ +25

Default Setting: 0

Connect a 50-Ohm dummy load and frequency counter to

the antenna jack; adjust the

[

SUB VFO-B

]

knob so that

the frequency counter reading is same as the VFO fre-

quency while pressing the PTT switch.

ADVICE:

Do not perform this Menu item unless you have a high-

performance frequency counter. Perform this Menu item

after aging the transceiver and frequency counter suffi-

ciently (at least 30 minutes).

MENU MODE

GENERAL GROUP

My FT2000D will not Transmit. Have not used it in over a year. I am sure it is something I have done wrong. Whe u puss PTT the signal goes to ZERO. Please Advise! Submitted on 12-9-2020 at 00:41
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-2000D in the language / languages: English as an attachment in your email.

The manual is 7,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Yaesu FT-2000D Manual

Product: