674720
35
Zoom out
Zoom in
Previous page
1/44
Next page
33
13. Remote Operation with External Controller
Repeater operation may be controlled remotely by connecting an external controller through the
[
CONTROL
I/O
]
connector at the back of the repeater.
The following features are available while in remote operation:
Change the communication mode of repeater transmit and receive
Turn the RX and TX tone signal “ON” or “OFF”
Monitor the discriminator analog or demodulated digital audio during up-link reception
To use the repeater under remote control, set up the repeater as explained below, after it is connected to the
external controller.
Turning remote operation ON/OFF
When the remote operation is “ON”, the repeater operates according to the control instructions received from
the external controller (the instructions are received through Pin 11 to Pin 14 of the
[
CONTROL I/O
]
connector).
When the remote operation is “OFF”, the repeater operates according to the settings determined through the
setup mode.
1 Touch
[
SETUP
]
.
The setup mode screen will appear.
2 Touch
[
F
]
.
The setup menu will appear.
3 Touch
[
MODE/REMOTE
]
.
The menu list will appear.
4 Touch
[
REMOTE
]
.
The set value will change between
[
OFF
]
and
[
ON
]
each time
[
REMOTE
]
is touched.
z Factory default: OFF
z Remote operation is not available in the “HRI + REPEATER MODE”.
SETUP Ver.1.xxx EXP A1
U
P
N
KI
L
N
KI
L
DO
WN
F
M/V SQL
Tx PWR
HI
BACK
BACK
ID SET
TIMER
ID AN NO UNCE
MODE/REMOTE
DG-ID
ID M OD E

SQL
R-OFF
T-OFF
DEVIATION
WIDE
REMOTE / COMMAND / DISP TIMER
M/V
BACK
BACK
>
COMMAND
>
DISPLAY TIMER
DG-ID
ON
REMOTE
ON
5 Touch
[
BACK
]
3 times.
The setting is determined and the display will return to the operation mode screen.
Note that
[
REMOTE
]
at the bottom left of the screen is displayed in red.
You can transmit by the microphone and PTT input of the front panel in all settings except AMS/AMS.
Control from external controller
To control the DR-1X remotely, optional cables can be used to connect
the repeater to an external controller.
Use the “CONTROL I/O” connector at the back of the repeater to con-
nect with the external controller.
To interface the DR-1X with an external controller, additional cables
with a 15-pin mini d-sub connector are needed to connect to the
“CONTROL I/O” connector. Your controller may also require rewiring.
Link operation may require four connections: receiver audio, transmit-
ter audio, receiver COR, and transmitter PTT; however, these are not
available on the “CONTROL I/O” connector.
The pin assignment of the “CONTROL I/O” connector is as follows.
Do not use a VGA cable for PC display to connect the external controller
to the repeater.
CONTROL I/O connector
5 - 1
10 - 6
15 - 11
(as viewed from real panel)
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu DR-1X-FR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu DR-1X-FR in the language / languages: English as an attachment in your email.

The manual is 14,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info