674720
14
Zoom out
Zoom in
Previous page
1/44
Next page
12
4. Set up Other Functions
Adjusting the squelch level
z When the squelch level is set to “open” the repeater will transmit, so the TX output must be connected to the duplexer
and antenna.
z Use extreme caution when making the squelch adjustment or measurement with a signal generator. Do not connect
the signal generator to the duplexer antenna port. To avoid damage to the test equipment, always connect the signal
generator directly to the RX antenna connector on the DR-1X.
z While the squelch level is being set, repeater transmit operation is temporarily permitted. This will facilitate checking
the performance of the Duplexer, and allow evaluation of the receiver sensitivity degradation (“desense”), during
simultaneous transmit/receive operation.
1 Touch
[
SETUP
]
.
The setup mode screen will appear.
2 Touch
[
SQL
]
.
When
[
SQL
]
turns yellow, the VOL meter below the RX band frequency
display, will change to the SQL meter and show the squelch level
setting.
3 Touch
[
]
or
[
]
to adjust the squelch level.
The level will be displayed in the SQL meter.
4 Touch
[
BACK
]
.
The squelch level is set, and the display will return to the operation
mode screen.
SETUP Ver.1.xxx EXP A1
PANEL1.XX DSP4.XX
3
7
U
P
N
KI
L
N
KI
L
8
7
DO
WN
M/V SQL
BACK
BACK
Adjusting the transmit power
1 Touch
[
SETUP
]
.
The setup mode screen will appear.
2 Touch
[
Tx PWR
]
to select the transmit power.
The setting is changed in the following sequence, each time
[
Tx PWR
]
is touched.
“HI” à “LO” à “MD” à
HI MD LO
50 W 20 W 5 W
3 Touch
[
BACK
]
.
The transmit power level is set, and the display will return to the
operation mode screen.
SETUP Ver.1.xxx EXP A1
PANEL1.XX DSP4.XX
3
7
U
P
N
KI
L
N
KI
L
8
7
DO
WN
F
M/V SQL
Tx PWR
HI
BACK
BACK
Adjusting the volume
Turn the VOL knob.
The VOL knob adjusts the audio volume level of the received (uplink) signal.
Turning the display ON and OFF
1 Press and hold the SETUP button to turn the display OFF.
When a display is OFF, operation of the touch panel will be locked.
The display will turn OFF automatically after a period of time (default 1
min) with no operation.
The display duration time setting may be selected from “1min”, “5min”,
“10min”, or “30min” (see page 27 “Setting the display turn-off time”).
2 Press and hold the SETUP button for 3 seconds to turn the display
ON.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu DR-1X-FR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu DR-1X-FR in the language / languages: English as an attachment in your email.

The manual is 14,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info