Manual Xterra TR6.4 TREADMILL (page 24 of 28) (English)

587181

Zoom out

Zoom in

1/28

TR6.4 Treadmill

Service Checklist - Diagnosis Guide

Before contacting us for aid, please review the following information. It may save you both time and expense.

This list includes common problems that may not be covered under the treadmill’s warranty.

1. Tether cord not in position.

2. Circuit breaker on front grill tripped.

Push circuit breaker in until it locks.

3. Plug is disconnected. Make sure plug is rmly pushed

into 115 VAC wall outlet.

4. Breaker panel circuit breaker may be tripped.

5. Treadmill defect. Contact XTERRA Fitness.

Display does not light

Tread-belt does not stay centered

Treadmill belt hesitates when

walked/run on

The user may be walking while favoring or putting more

weight on either the left or right foot. If this

walking pattern is natural, track the belt slightly

off-center to the side opposite from the belt

movement. See General Maintenance section on

Tread-belt Tension. Adjust as necessary.

1. If the belt moves, but stops after a short time and thedis

play shows “LS”, run calibration.

2. If you press Start and the belt never moves, then the

display shows LS, contact service.

Motor is not responsive after

pressing Start

Treadmill will only achieve

approximately 7 mph but shows higher

speed on display

This indicates motor should be receiving power to

operate. Low AC voltage to treadmill. Do not use an

extension cord. If an extension cord is required it should be

as short as possible and heavy duty 16 gauge minimum.

Low voltage. Contact an electrician or XTERRA Fitness. A

minimum of 110 volt AC current is required.

High belt/deck friction. See General Maintenance section

on cleaning the deck. If cleaning doesn’t prevent this from

reoccurring, check to see if there is signicant wear of the

deck. If so, the deck may need to be ipped if it is on its

original side

Tread-belt stops quickly/suddenly

when tether cord is pulled

High belt/deck friction. See General Maintenance. If

cleaning doesn’t prevent this from reoccurring, check the

amp draw of the motor. If this is high and there are signs of

signicant wear of the deck, it may need to be ipped if it is

on its original side

Treadmill trips on board 15 amp circuit

Treadmill may not be grounded. Static electricity is

“crashing” the computer. Refer to Grounding

Instructions on page 3.

Computer shuts off when console is

touched (on a cold day) while

walking/running

Need to replace the breaker with a “High In-rush

current” type breaker (see page 3 for details)

Circuit breaker trips, but not the

treadmill circuit breaker

Problem Solution/Cause

I have xterra TR6.4. I'm getting a LS code. I tried calibrating it. It been in calibrating mode for several hours and nothing. Is there a solution to this issue? Submitted on 11-7-2020 at 04:42
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Xterra TR6.4 TREADMILL in the language / languages: English as an attachment in your email.

The manual is 2,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Xterra TR6.4 TREADMILL Manual

Product: