587192
19
Zoom out
Zoom in
Previous page
1/22
Next page
TR450_TR550 Treadmill
18
TREADBELT TRACKING ADJUSTMENT:
The performance of your treadmill is dependent on the frame running on a reasonably level
surface. If the frame is not level, the front and back roller cannot run parallel, and constant belt
adjustment may be necessary.
The treadmill is designed to keep the tread-belt reasonably centered while in use. It is normal
for some belts to drift near one side while the belt is running with no one on it. After a few
minutes of use, the tread-belt should have a tendency to center itself. If, during use, the belt
continues to move toward one side, adjustments are necessary.
TO SET TREADBELT TRACKING:
A 6 mm Allen wrench is provided to adjust the rear roller. Make tracking adjustments from the
left side only. Set belt speed at
approximately 2 to 3 mph. A small
adjustment can make a dramatic difference.
Turn the bolt only a 1/4 turn and wait a few
minutes for the belt to adjust itself.
Continue to make 1/4 rotation turns until
the belt stabilizes in the center of the
running deck. The belt may require
periodic tracking adjustment depending on
use and walking/running characteristics.
Some users will affect tracking differently.
Expect to make adjustments as required to center the tread-belt. Adjustments will become less
of a maintenance concern as the belt is used. Proper belt tracking is an owner responsibility
common with all treadmills.
ATTENTION:
DAMAGE TO THE RUNNING BELT RESULTING FROM IMPROPER TRACKING /
TENSION ADJUSTMENTS IS NOT COVERED UNDER THE XTERRA WARRANTY.
MAINTENANCE MODE:
If you want to set the Speed and Distance to Metric or if there is a problem with the speed and
you would like to perform the calibration procedure, use the Maintenance Mode. To enter
Maintenance Mode press, and hold for 5 seconds, the Start and Fast keys while installing the
safety key. All the segments will light then the message window will display software versions
and tell you to press Enter.
The message window will now be showing the setting for English (miles) or Metric
(Kilometers) Use the up/down keys to select and press enter
The message window will ask to adjust the.Wheel size for calibration. Enter 2.83.
The display will show a number for the lowest speed setting (for miles the number
should be 0.5). Adjust the low speed setting with the Fast/Slow keys and press Enter.
The display will show a number for the top speed setting (for Miles it should be 12.0).
The display will ask for top incline setting, enter 12 for TR450 and 15 for TR550.
The display will ask for grade return. This will reset the incline to zero, when set to ON,
when you stop a program.
Press Start to begin calibration. This is an automatic process, the belt will move and
change speeds without warning, Be Careful! When calibration is done, the console will
return to the start-up screen.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Xterra TR550 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Xterra TR550 in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info