587179
21
Zoom out
Zoom in
Previous page
1/23
Next page
TR6.2 Treadmill
20
BELT / DECK LUBRICATION:
Do not lubricate with other than Xterra approved lubricant. Your treadmill comes with one tube of
lubricant and extra tubes can be ordered directly from Xterra. There are commercially available
lube kits, but the only one currently approved by Xterra is Lube-N-Walk. These kits come with an
application wand that makes applying the lubrication easier. The kits can be purchased from
Xterra.
Keeping the deck lubricated at the recommended intervals ensures t
he longest life possible for
your treadmill. If the lubricant dries out, the friction between the belt and deck rises and places
undue stress on the drive motor, drive belt and electronic motor control board, which could result
in catastrophic failure of these expensive components. Failure to lubricate the deck at regular
intervals may void the warranty.
The deck comes pre-lubricated and subsequent lubrication should be performed every 180 hours
of use. The console has a built in
lubrication reminder indicator that lights every 180 hours of use.
To lubricate the deck with the tube of lubricant supplied it will be necessary to loosen the walking
belt. Using the 6 mm allen wrench supplied, loosen the two rear roller adjustment bolts -- located
in the rear end caps – enough to get your hand under the belt (5 –10 turns). Make sure to loosen
both bolts the same amount of turns and also remember how many turns, because when finished
you will need to tighten the bolts
back to the point they were before.
Once the belt is loose, wipe the deck with a clean lint free cloth to remove any dirt. Apply the
whole tube of lubricant onto the deck surface about 18 inches from the motor cover. Squeeze out
the contents of the tube across the deck (parallel to the motor cover) in about a one-foot long line,
like toothpaste on a toothbrush. The one-foot line should be in the middle of the deck at
approximately equal distance from both side edges of the belt.
You want the lubricant to be
applied about the spot that your feet would hit the belt as you are walking. This should be about
18 inches from the motor cover, but you may want to walk on the treadmill before loosening the
belt to note where your feet land on the belt. If you mostly run on the treadmill, the spot where
your feet land may be different from walking.
Once the lubricant is applied, tighten the rear roller bolts the same amount of turns as when you
loosened them. Run the treadmill
at about 6 mph without walking on it for about a minute or two
to make sure the belt stays in the middle of the deck. If the belt tracks to one side then follow the
belt tracking instructions to remedy. Now the deck is lubricated and you should walk, not run, on
the treadmill immediately for at least 5 minutes to ensure the lubricant is evenly distributed. If you
purchase a Lube-N-Walk kit, follow the instructions that come with it to apply the lubrication.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Xterra TR 6.2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Xterra TR 6.2 in the language / languages: English as an attachment in your email.

The manual is 3,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info