797313
4
Zoom out
Zoom in
Previous page
1/20
Next page
RS485
1 km max / 32 Units (EWS + Biometric Readers)
TCP/IP gnd gnd
Stub
max. 5m
Jumper for
RS485 termination
5.1 CONNECTING BIOMETRIC READERS IN SAME RS485 LINE WITH THE EWS CONTROLLERS
The Biometric readers are connected through RS485 bus. The same RS485 bus that the EWS controllers are connected to.
Maximum units in one network (EWS + Biometric readers) is 32.
If there are more than 32 units in one network, please utilize RS 485 HUB to connect.
The RS485 Line should be configured in the form of a daisy chain, NOT in a form of a star. If star must be used in some points, keep
the stubs from the RS485 backbone as short as possible. Maximum length of the stub is dependant of the installation (total
number of devices in RS485 line (total cable length, termination, cable type...) so recommendation is to keep stubs shorter than
5 meters, keeping in mind that this can be possible reason for errors in communication with PC software
The cable must be twisted and shielded with a min. 0.2 mm2 cross section.
Connect the ground (0V) of each unit in the RS 485 Line using a third wire in the same cable.
The shield of the communication cable between two devices must be connected to the EARTH from ONE side of the RS 485 Line.
Use the side that has earth connection to the buildings grounding network.
- The Biometric readers can be connected to virtually any controller that conforms to Wiegand format standards (standard
Wiegand 26bit or self-defined Wiegand).
- The lines D0 and D1 are the Wiegand lines and the Wiegand Number is sent through them.
- The RS485 line (A, B) is used for fingerprint transfer and reader settings.
- The Biometric readers must be powered from the controller.
- If you use different power supply for the biometric reader, connect the GND from the both devices to ensure correct transfer of
the wiegand signal
- When you have connected the reader and powered on, the LED should flash in orange light + 2 beeps. This lets you know it's on
and ready for use.
- Fingerprint enrollment is done from the PC Software. Connection between the Biometric readers and the PC must be
established.
5. CONNECTING BIOMETRIC READERS TO EWS CONTROLLER
50 ohm 50 ohm
LD16
R55
C41
C28
L2
R36
LD20
R18
R25
R24
C40
R10
C34
L10
L11
C18
C33
R9
C42
C1
R5
R45
C43
C44
R28
R21
C45
D13
LD14
R46
C3
C5
R38
ZD3 C29
L9
LD13
R14
ZD4 C32
R19
R37
ALD17 ALD19
ALD18
L7
C27
L6
C16
C15
RX4
D5
D10
R32 R33 R35
R49
IC6
ZD5
ZD6
R22
L3
R53
R34
TAS1
IC11
R15
IC15
R3
R4
L8
R47
FUSE1
IC8
R20
R16
R11
C2
X1
C4
IC7 ICN2
R1
C13
C12
ICN1
R23
R48
A
LD5
RE1 RE3
A
LD8
X3
IC1
C6
U5
L5
L4
RE4RE2
A
LD6 A
LD9
ZD2
LD15
R13
ZD1
R54
R50
R6
IC12 R17
R7
R62
ALD23
D3
D2
RX3
J1
Rb6
R2
LD21
IC2
H1 ALD22
BAT
U1
IC5
FUSE2
IC3
U4
A
A
IC1
A
A
A
A
Earth
screw
Free Led 1
Free Led 2
GND
12V out
D0
D1
Free Led 1
Free Led 2
GND
12V out
D0
D1
Door Sensor2
Door Sensor1
Exit Button1
Exit Button2
GND
GND
Free In 2 -
Free In 2 +
Free In 1 -
Free In 1 +
Rx Tx Busy System
OK
Door 1 Door 2 Free Out 1 Free Out 2
TCP/IP Earth
12Vdc Out
12V
gnd
D1
D0
12V
gnd
led2
led1
12V
IN1
IN1
IN2
IN2
+
-
+
-
D1
D0
12V
gnd
led2
led1
PB2
PB1 DS2DS1
gnd gnd
COM
NC1NO1 NC2NO2
COM
COM
NC3NO3 NC4NO4
COM
GND
BA
gnd
Fuse
Ser No: 11-04-16-013
Mac: 00-04-A3-16-90-D
RoHS
3 3 6 1 1 1 0 1 3 1
pink
violet
green
orange
black
red
white
yellow
50m. max
B
+12V
LG-
D1
D0
LR-
GND
A
4
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for XPR B100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of XPR B100 in the language / languages: English as an attachment in your email.

The manual is 4.71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of XPR B100

XPR B100 User Manual - German - 20 pages

XPR B100 User Manual - Dutch - 20 pages

XPR B100 User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info