730152

Xiaomi Mi Smart Home Kit Manual

3
Zoom out
Zoom in
Previous page
1/4
Next page
Installation
Distance for the eective operation of the device: select a
suitable site for the installation of the sensor, it is necessary
to reset the factory settings using a special needle. After this
multi-function gateway will make a corresponding sound,
which signals that you chose the optimal distance between
the sensor and a multi-function gateway.
Motion Sensor
Method 1: You do not have to stick with the back of the
sensor to the wall or other surface, you can simply install it
in the right place.
Method 2: Remove the protective cover (in kit of your device
you get adhesive membrane) and you can stick the sensor
to the back of any surface or wall.
* Optimal height at which the sensor should be, 1.2-2.1m.
At a height of less than 1.2 m, the detection range becomes
smaller, but it does not aect its use. When you place the
sensor more than 2.1m, in the room will appear blind spots,
so there can be problems with nding people, animals.
* During installation, pay special attention to induction lens.
It should be directed to the side of space that you want to
monitor. Install or stick the sensor maximum close to the
edge of a table or cabinet.
1 Stick to any desired surface
Remove the protective
membrane
Optimal detection range / Optimal detection radius
Sensor for windows / doors
1 Remove the protective membrane
During installation, try
as much as possible to
balance the location of
the primary sensor and
the magnet at a special
mark (see Figure 2)
Attach the device to the desired
surface (recommended to
install the primary sensor on the
immovable surface, and a magnet
on the surface, which is expected
to be opened. The allowable
distance between the main
sensor and magnet 22mm.
The main hub
1 Remove the protective membrane
2 Attach the unit to the desired
surface
* Glue unit on a dry surface
* Place the hub on the main non-metallic surface, since it
aects its work
New devices
To add a new device or restore the factory settings, you
can use one of the two following methods:
Method 1: Open the smart home and on the main page
of the multifunction gateway click on «add device» by
following the instructions set out below, do a factory reset.
Method 2: Continuously press three times on button of a
multifuntion gateway, follow the instructions set out below,
do a factory reset.
* When you connect smart devices without a hole for reset,
read the instructions for use of such a device
* When connecting the device to another gateway, you
need to reset the device, and then add a new device by
following the above described scheme.
XIAOMI-MI.COM
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Xiaomi Mi Smart Home Kit at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Xiaomi Mi Smart Home Kit in the language / languages: English as an attachment in your email.

The manual is 1,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info