212706
80
Zoom out
Zoom in
Previous page
1/98
Next page
DocuMate 162 Scanner User’s Guide 75
Maintenance
Status Light Troubleshooting Codes
The status light indicates the current state of the scanner. A blue status
light indicates the normal state of the scanner. A red status light indicates
that there is a hardware issue. Descriptions of the most common patterns
are listed below.
Normal Operation
Blinking blue: indicates the scanner is waking up from power saving
and preparing to scan.
Steady blue: indicates the scanner is ready to scan.
Steady red: indicates the scanner is busy.
Error Codes
If your scanner experiences hardware problems, the status light will blink
red, and the LED flashes an “E” and then the error code number.
In all cases you should turn off your scanner and check your scanner
setup. Open the scanner and make sure your input tray is fully seated in
the scanner casing, make sure your ADF pad is securely snapped in
place, verify the connections to the PC and wall.
The LED blinks back and forth
between “E” and the error code
number (such as 8).
The red light flashes the
number of times as the error
code (8 in this example).
Error
Code Problem Description Solution
0 The scanner is not
communicating with the
computer.
Make sure the USB cable is plugged in. If the USB cable is plugged into
a hub or keyboard, try plugging it directly into the back of the computer.
Try a different USB port on the computer or a different USB cable.
4 or 5 The scanner lamp is
either turned off or the
lamp has not warmed up
enough to initiate
scanning.
In the One Touch hardware properties turn the scanner lamp on. See
page 58 for instructions. If the lamp is already on, turn the lamp off then
on again. If the problem persists and your scanner’s power is plugged
into a surge protector or UPS battery backup, try plugging the scanner
power directly into a wall outlet.
6 The scanner is open. Make sure the scanner lid is fully closed after performing maintenance
on the scanner or removing a jammed page.
7 or 8 The paper input tray is
not fully seated into the
scanner casing.
Open the scanner and take off the input tray. Place the input tray back
into the scanner and press it back until it snaps into place. See page 5
for instructions to install the tray.
9 Paper jam Open the ADF cover and remove the jammed page.
All
Other
Codes
An internal part in the
scanner may have
malfunctioned.
Re-boot your computer. If the problem persists, contact Xerox Technical
Support.
80


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Xerox documate 162 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Xerox documate 162 in the language / languages: English as an attachment in your email.

The manual is 4,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Xerox documate 162

Xerox documate 162 User Manual - German - 104 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info