Manual Xenyx X1832USB xenyx x1832usb (page 6 of 19) (Dutch)

751068

Zoom out

Zoom in

1/19

6XENYX X2442USB/X2222USB/X1832USB/X1622USB User Manual

MIC

Each mono input channel oers a balanced microphone input via the XLR

connector and also features switchable +48 V phantom power supply for

condenser microphones. The XENYX preamps provide undistorted and noise-free

gain as is typically known only from costly outboard preamps.

◊ Please mute your monitor system before you switch on phantom

power. Otherwise potentially damaging thumps will be sent to

your speakers. Please also note the instructions in chapter 5.5

“Voltage supply, phantom power and fuse”.

LINE IN

Each mono input also has a balanced line input on a ¼" jack. You can also connect

unbalanced devices using mono jacks to these inputs.

◊ Please remember that you can use either the microphone input or the

line input of a channel, but not both at the same time!

INSERT

◊ Insert points enable the processing of a signal with dynamic processors

or equalizers. They are sourced pre-fader, pre-EQ and pre-aux send.

Detailed information on using insert points can be found in chapter 5.3.

◊ Unlike the X2442USB, the X1622USB, X1832USB and X2222USB have

their insert points located on the rear of the console.

GAIN

Use the GAIN control to adjust the input gain. This control should always be

turned fully counter-clockwise whenever you connect or disconnect a signal

source to one of the inputs.

The scale has 2 dierent value ranges: the rst value range (+10 to +60 dB)

refers to the MIC input and shows the amplication for the signals fed in there.

The second value range (+10 to -40 dB) refers to the line input and shows its

sensitivity. The settings for equipment with st andard line-level signals (-10dBV

or +4 dBu) look like this: While the GAIN control is turned all the way down,

connect your equipment. Set the GAIN control to the external devices’ standard

output level. If that unit has an output signal level display, it should show 0 dB

during signal peaks. For +4dBu, turn up GAIN slightly, for -10 dBV a bit more.

Fine-tuning of a signal being fed in is done using the level meter. To route the

channel signal to the level meter, you have to press the SOLO switch and set the

MODE switch in the main section to PFL (LEVEL SET).

Using the GAIN control, drive the signal to the 0-dB mark. This way you have

a vast amount of drive headroom for use with very dynamic signals. TheCLIP

display should light up only rarely, preferably never. While ne-tuning,

theequalizer should be set to neutral.

LOW CUT

Additionally, the mono channels of the mixing consoles have a high-slope

LOWCUT lter for eliminating unwanted, low-frequency signal components

(75Hz, 18 dB/octave).

COMPRESSOR

Each mono channel features a built-in compressor which lowers the dynamic

range of the signal and increases its perceived loudness. The loud peaks are

squashed down and the quiet sections are boosted.

Turn the COMP knob clockwise to add more compression eect. The adjacent LED

with light when the eect is engaged.

2.1.2 Equalizer

All mono input channels have a 3-band equalizer with semi-parametric mid

bands. All bands provide boost or cut of up to15 dB. In the central position,

theequalizer is o (at).

The circuitry of the British EQs is based on the technology used in the best-known

top-of-the-line consoles and providing a warm sound without any unwanted

side eects. The result are extremely musical equalizers which, unlike simple

equalizers, cause no side eects such as phase shifting or bandwidth limitation,

even with extreme gain settings of ±15 dB.

All Models

Fig. 2.2: Equalizer of the input channels

The upper (HIGH) and the lower (LOW) bands are shelving lters that increase

or decrease all frequencies above or below their cut-o frequency. The cut-o

frequencies of the upper and lower bands are 12 kHz and 80Hz respectively.

Forthe mid range, the console features a semi-parametric equalizer with a

lter quality (Q) of 1 octave, tunable from 100 Hz to 8 kHz. Use the MID control

to set the amount of boost or cut, and the FREQ control to determine the

centralfrequency.

2.1.3 Monitor and eects busses (Aux Sends)

X1622USB X2442USB

Fig. 2.3: Aux Send control MON and FX in the channel strips

Monitor and eects busses (AUX sends) source their signals via a control from

one or more channels and sum these signals to a so-called bus. This bus signal

is sent to an aux send connector (for monitoring applications: MON OUT) and

then routed, for example, to an active monitor speaker or external eects device.

Inthe latter case, the eects return can then be brought back into the console via

the aux return connectors.

All monitor and eects busses are mono, are tapped into post EQ and oer

amplication of up to +15 dB.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Xenyx X1832USB xenyx x1832usb in the language / languages: Dutch as an attachment in your email.

The manual is 5,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Xenyx X1832USB xenyx x1832usb Manual

Product: