608044

Xavax 00111932 - MAX Starter Kit Manual

15
Zoom out
Zoom in
Previous page
1/42
Next page
14
2.3. Mounting
The MAX! Window Sensor essentially consists of two elements: a magnet (1) and an electronic unit
(2). One of these must be mounted on the frame, the other on the window.
• First select the window that is frequently used for ventilation and which the window sensor is to be
attached to.
• The magnet (1) can be installed on either side of the electronic unit (2). Installati- on
must be in parallel with a maximum spacing of 8 mm (A).
• The window sensor can be attached both vertically and horizontally.
• The magnet (1) must be centre-aligned with the electronic unit (2) (C).
• The magnet (1) and electronic unit (2) must be attached at the same level or as close to the same level
as is possible within the space (B). You might need to use the spacers supplied for the magnets (1) to do this.
Each of the elements can be fastened in two ways:
Adhesive strip method:
The surface must be clean and dry.
Using adhesive strips does not damage the door or window in any way.
• Stick the adhesive strips supplied with the device on the rear sides of the brackets (1 and 2).
• Then press the brackets onto the frame and window.
Screw method:
Using screws damages the window frame.
• Use a pen to mark the bore hole positions (a) on the window frame and casement.
• If you are working with a hard surface, you should drill the holes marked (a) using
a 1.5 mm drill.
• Use the countersunk head screws supplied to fasten the wall brackets for the electronic
unit (2) and magnet (1).
If you are using the 14.5 mm high spacer, you must rst fasten it with two 2.2 x 16 mm screws and
then attach the magnet unit (1) to it with another two screws. The atter spacers are simply fastened
together with the magnet using two 2.2 x 16 mm screws.
• Once you have fastened the wall bracket for the magnet (1) insert the magnet. Then place the cap on the magnet.
• Once you have fastened the wall bracket for the electronic unit (2), attach the electronic unit. Then place the cap (white
and brown caps are supplied with the device) on the electronic unit.
Screw fastening damages the window frame. For those living in rented accommodation, this could lead to a
landlord making a claim for compensation or holding back a tenant’s deposit.
2.4. Inserting (replacing) batteries
The window sensor runs on 2 LR03
(micro/AAA) batteries.
• Remove the cover on the electronic unit by pulling it forward and off the device (1). To release the co-
ver, squeeze it gently from above and below with your thumb and index nger (4).
• Carefully lift the release clip (2) from the side.
• Pull the electronic unit forward (3) and off the bracket.
• After removing the old batteries, please wait approximately 60 seconds before inserting the new ones.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Xavax 00111932 - MAX Starter Kit at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Xavax 00111932 - MAX Starter Kit in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info