Manual Worx WX722 (page 13 of 120) (English, German, Dutch, French, Italian, Polish, Spanish)

575100

Zoom out

Zoom in

1/120

Angle grinder EN

WHEEL GUARD FOR CUTTING

WARNING! For cutting metal,always

work with the wheel guard for

cutting(14). The wheel guard for cutting (14)

is mounted in the same manner as the wheel

guard for grinding(5).

3. FITTING THE DISCS (See Fig. C1.C2)

Put the inner ﬂange onto the tool spindle.

Ensure it is located on the two ﬂats of spindle.

Place the disc on the tool spindle and inner

ﬂange. Ensure it is correctly located. Fit the

threaded outer ﬂange making sure it is facing

in the correct direction for the type of disc

ﬁtted. For grinding discs, the ﬂange is ﬁtted

with the raised portion facing towards the

disc. For cutting discs, the ﬂange is ﬁtted

with the raised portion facing away from the

disc (See Fig. C1).

Press in the spindle lock button and rotate

the spindle by hand until it is locked. Keeping

the lock button pressed in, tighten the outer

ﬂange with the spanner provided.

(See Fig. C2).

4. SAFETY ON/OFF SWITCH (See Fig. D)

Your switch is locked off to prevent

accidental starting. With your hand on the

on/off switch (a) use your ﬁnger to push

lever (b) forward and then depress on/off

switch (a). Then release lever (b). Your tool

is now on. To switch off just release on/off

switch.

SOFT START MOTOR(WX722.1)

Internal electronic components allow the

motor speed to increase slowly, which

reduces the“twisting”effect on your wrists

due to the high power motor.

5. VARIABLE SPEED CONTROL

(See Fig. E)(WX722/WX722.1)

Adjust the thumb-wheel to increase or

decrease the speed (See Fig. E) according

to the material, material thickness and disc/

accessory speciﬁcation to be used (also

possible during no load operation). See Table

1 for general guidance on speed selection.

Avoid prolonged use at very low speeds

as this may damage your angle grinder’s

motor. The constant speed control electronic

circuit inside your angle grinder maintains a

nearly constant speed even when your angle

grinder is under load.

Table 1

Material Speed setting

Grinding ferrous metals,

cutting stone, brick, etc,

Wire cup brush

5-6

Grinding or sanding non-

ferrous metals, light grind-

ing work

3-5

Polishing, light sanding work 1-3

6. SPINDLE LOCK BUTTON

Must only be used when changing a disc.

Never press when the disc is rotating!

7. TO USE THE GRINDER

ATTENTION: Do not switch the

grinder on whilst the disc is in

contact with the workpiece. Allow the

disc to reach full speed before starting

to grind.

Hold your angle grinder with one hand on the

main handle and other hand ﬁrmly around

the auxiliary handle.

Always position the guard so that as much

of the exposed disc as possible is pointing

away from you.

Be prepared for a stream of sparks when the

disc touches the metal.

For best tool control, material removal

and minimum overloading, maintain an

angle between the disc and work surface of

approximately 150 -300 when grinding.

Use caution when working into corners as

contact with the intersecting surface may

cause the grinder to jump or twist.

When grinding is complete allow the

workpiece to cool. Do not touch the hot

surface.

8. CUTTING

WARNING! For cutting metal, always

work with the wheel guard for cutting.

When cutting, do not press, tilt or oscillate

the machine. Work with moderate feed,

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX722 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2,29 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX722 Manual

Product: