Manual Worx WX701 (page 13 of 120) (English, German, Dutch, French, Italian, Polish, Spanish)

575107

Zoom out

Zoom in

1/120

Angle grinder EN

1312

6. TO USE THE GRINDER (See Fig. E)

ATTENTION: Do not switch the grinder

on whilst the disc is in contact with the

workpiece. Allow the disc to reach full speed

before starting to grind.

Hold your angle grinder with one hand on the

main handle and other hand ﬁrmly around the

auxiliary handle.

Always position the guard so that as much of the

exposed disc as possible is pointing away from you.

Be prepared for a stream of sparks when the disc

touches the metal.

For best tool control, material removal and minimum

overloading, maintain an angle between the disc

and work surface of approximately 15

-30

when

grinding.

Use caution when working into corners as contact

with the intersecting surface may cause the grinder

to jump or twist.

When grinding is complete allow the workpiece to

cool. Do not touch the hot surface.

7. CUTTING

WARNING! For cutting metal,always

work with the wheel guard for cutting.

When cutting, do not press, tilt or oscillate the

machine. Work with moderate feed, adapted

to the material being cut.

Do not reduce the speed of running down

cutting discs by applying sideward pressure.

The direction in which the cutting is performed

is important.

The machine must always work in an up-

grinding motion. Therefore, never move the

machine in the other direction! Otherwise, the

danger exists of it being pushed uncontrolled

out of the cut.

WORKING HINTS FOR YOUR

ANGLE GRINDER

1. Always start at no load to achieve

maximum speed then start working.

2. Do not force the disc to work faster,

reducing the Disc’s moving speed means

longer working time.

3. Always work with a 15-30 angle between

disc and workpiece. Larger angles will

cut ridges into the workpiece and affect

the surface ﬁnish. Move the angle grinder

across and back and forth over the

workpiece.

4. When using a cutting disc never change the

cutting angle otherwise you will stall the

disc and angle grinder motor or break the

disc. When cutting, only cut in the opposite

direction to the disc rotation. If you cut in

the same direction as the disc rotation the

disc may push itself out of the cut slot.

5. When cutting very hard material best

results can be achieved with a diamond

disc.

6. When using a diamond disc it will become

very hot. If this happens you will see a full

ring of sparks around the rotating disc.

Stop cutting and allow to cool at no load

speed for 2-3 minutes.

7. Always ensure the workpiece is ﬁrmly held

or clamped to prevent movement.

MAINTENANCE

Remove the plug from the socket before

carrying out any adjustment, servicing or

maintenance.

There are no user serviceable parts in your

power tool. Never use water or chemical

cleaners to clean your power tool. Wipe clean

with a dry cloth. Always store your power tool

in a dry place. Keep the motor ventilation slots

clean. Keep all working controls free of dust.

Occasionally you may see sparks through the

ventilation slots. This is normal and will not

damage your power tool.

If the supply cord is damaged, it must be

replaced by the manufacturer, its service agent

or similarly qualiﬁed persons in order to avoid

a hazard.

TROUBLESHOOTING

Although your new angle grinder is really

very simple to operate, if you do experience

problems, please check the following:

1. If your grinder will not operate check the

power at the main plug.

2. If your grinder wheel wobbles or vibrates,

check that outer ﬂange is tight; check that

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX701 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX701 Manual

Product: