Manual Worx WX676.7 (page 10 of 132) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

575122

Zoom out

Zoom in

1/132

Oscillating Tool EN

OPERATION INSTRuCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

INTENDED USE

The power tool is intended for sawing and

remodelling wooden materials, plastic,

plaster, non-ferrous metals and fasteners

(e.g. nails and clamps) as well as for working

on soft wall tiles and for dry grinding of small

surfaces. It is especially suitable for working

close to edges and for ﬂush cutting.

1. MOUNTING ACCESSORIES

CAUTION: For all work or when

changing accessories, always wear

protective gloves. Avoid danger of injury

from the sharp edges of the accessories.

Accessories can become very hot while

working, presenting danger of burns! Make

sure the tool is unplugged prior to

changing accessories.

WARNING: To reduce the risk of

injury, do not let the sharp side of

the accessory face back toward the

user’s hand.

- Loosen the Flange

Use the Allen Key to rotate the Flange

clockwise. (See Fig. A)

- Insert Accessories

Insert the Accessory onto the Universal Fit

Accessory Interface. (See Fig. B)

- Tighten the Flange

- Use the Allen Key to rotate the Flange

counterclockwise until accessory is tightened

securely. (See Fig. C)

NOTE: For prior model Worx Sonicrafter

hex-interface accessories and most other

non-WORX branded accessories, the Flange

must be completely removed to install

accessory (See Fig. D).

2. MOUNTING/CHANGING THE

SANDING SHEET (See Fig. E)

Align the sanding sheet and press it onto the

sanding pad by hand.

Firmly press the power tool with the sanding

sheet against a ﬂat surface and brieﬂy switch

the power tool on. This provides for good

adhesion and prevents premature wear.

If one point has become worn, pull off the

sanding sheet, turn it 120° and place it on

again.

NOTE: For other various brands’ sanding

pad, use small ﬂange provided.

3.MOUNTING THE SUCTION DEVICE

(See Fig. F-J)

When vacuuming, mount the suction device

as shown in F-J.

NOTE: Using the sanding pad perforated. You

can only do the vacuuming after ﬁtting the

dust collector.

4. OPERATING THE ON/OFF SWITCH

To start the machine, push the On/Off switch

forward so that the “I” is indicated on the

switch.

To switch off the machine, push the On/Off

switch toward the rear so that the “0” is

indicated on the switch.

5 USING THE VARIABLE SPEED DIAL

Select oscillation frequency (speed) while the

motor is running.

The Variable Speed Dial can be used to set

the optimum oscillating frequency according

to the accessories used and the respective

application.

High oscillation frequency:

Sanding, sawing, rasping and polishing stone

and metal.

Low oscillation frequency:

Scraping, polishing varnishes.

6. SANDING

Typical application: wood, metal; small areas,

especially corners, edges and places difﬁcult

to access.

Select high oscillation frequency.

Sand with a constant movement and light

pressure.

Heavy pressure does not increase the

removal – the sanding sheet merely wears

faster.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX676.7 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX676.7 Manual

Product: