575130

Worx WX673.3 Manual

11
Zoom out
Zoom in
Previous page
1/128
Next page
High frequency multi-function tool EN
11
of injury from the sharp edges of the
application tools. Application tools can
become very hot while working, presenting
danger of burns!
WARNING: To reduce the risk of
injury, do not let the Universal end
cut blades or any segment saw blades
face back toward the user’s hand.
Unscrew the fastening piece (8).
Clean the tool holder, the application tool and
the fastening piece (8).
Place the application tool exactly onto
the hex-shaped tool holder. Note that the
application tool has a flush fit.
Reposition the fastening piece (8) using the
supplied allen key.
2. ADAPTER (21) (See Fig.
B3
)
Accessories of other brands (Fein
®
, Bosch
®
)
can be fitted onto the Sonicrafter
®
brand tool
using the adapter.
NOTE: Fein is a registered trademark of
C. & E. Fein GmbH. Bosch is a registered
trademark of Robert Bosch GmbH.
1) Use the allen key (23) to unscrew the
fastening piece (8) and then remove it
from the tool holder.
2) Clean the tool holder, the adapter the
application tool and the fastening piece.
3) Fit the adapter onto the tool holder,
then place the application tool onto the
adapter. Make sure that the tool holder,
the adaptor, and the application tool share
a flush fit.
4)
Reposition the fastening piece onto the
application tool and tighten with the allen key.
NOTE: Make sure the adapter matches the
application tool. The adapter (I) is matched to
the application tool of Fein
®
. The adapter (II)
is matched to the application tool of Bosch
®
.
(See Fig. B3)
3. MOUNTING/CHANGING THE
SANDING SHEET (See Fig. C)
Align the sanding sheet and press it onto the
sanding pad by hand.
Firmly press the power tool with the sanding
sheet against a flat surface and briefly switch
the power tool on. This provides for good
adhesion and prevents premature wear.
If one point has become worn, pull off the
sanding sheet, turn it 120° and place it on
again.
4. OPERATING THE ON/OFF SWITCH
To start the machine, push the On/Off switch
(2) forward so that the “I” is indicated on the
switch.
To switch off the machine, push the On/Off
switch (2) toward the rear so that the “0” is
indicated on the switch.
5. USING THE VARIABLE SPEED
CONTROL
Select oscillation frequency (speed) while
the motor is running.
The variable speed control (5) can be used
to set the optimum oscillating frequency
according to the accessories used and the
respective application.
High oscillation frequency:
Sanding, sawing, rasping and polishing
stone and metal.
Low oscillation frequency:
Polishing varnishes.
6. MOUNTING THE SUCTION DEVICE
(See Fig. D1, D2)
When vacuuming, mount the suction device
as shown in D1-D2.
NOTE: Using the sanding pad perforated.
You can only do the vacuuming after fitting
the dust collector.
7. SANDING
Typical application: Wood, metal; small
areas, especially corners, edges and places
difficult to access.
Select high oscillation frequency.
Sand with a constant movement and light
pressure.
Heavy pressure does not increase the removal
– the sanding sheet merely wears faster.
8. SAWING WITH THE SEGMENT SAW
BLADE
Typical application: Wood, plastics, sheet metal.
Select high oscillation frequency.
The saw blade lasts longer if the wear
is distributed evenly. To ensure an even
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX673.3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX673.3 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info