Manual Worx WX625 (page 11 of 128) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

575097

Zoom out

Zoom in

1/128

Perpendicular planer EN

11 10

belt runs exactly along the length grooves of

the pinion and the pulley.

NOTE: Place the belt cover (11) back on

top and tighten it with screw.

7. FITTING A DUST BAG

This accessory can be ﬁtted by sliding the dust

bag inlet over the planer dust extraction (5) as

far as possible. The dust bag will reduce the

efﬁciency of the exhaust system and the bag

must be emptied frequently to maintain the

efﬁciency. To empty, open the zip on the rear

of the dust bag.

NOTE: This accessory can be used for

smaller jobs.

8. EXTERNAL DUST EXTRACTION

The dust extraction (5) is best connected to a

suitable external dust extraction machine e.g.

vacuum cleaner.

9. REPLACING CARBON BRUSH

WARNING: Always be sure that the

tool is switched off and unplugged

before attempting to perform inspection

or maintenance. The motor brush can be

easily accessed the motor housing.

ATTENTION: When servicing a tool,

ALWAYS use only identical replacement

parts.

STEP 1: Locate the plastic motor brush

caps on both the front and back of the motor

housing.

STEP 2: Remove the threaded brush cap on

accessible carbon brush (20) with a ﬂathead

screwdriver and turn the screw in a counter-

clockwise rotation to loosen.

STEP 3: Gently remove the old motor brush.

STEP 4: Carefully insert the replacement

brush. Ensure the brush is completely inserted

into the holder and is seated properly and is

free to move inside its holder.

STEP 5: Replace the brush cap with the ﬂat-

head screwdriver, turning clockwise to tighten.

Do not apply excessive force as this may

damage the access brush caps.

10. PERPENDICULAR GUIDE FENCE (18)

The Perpendicular Fence can be used to

provide accurate results for all edge planing

operations including squaring the face,

straightening an edge and rebating.

18.1 Lock nut (2 places)

18.2 Adjusting turnbuckle (front and rear)

18.3 T section guide

18.4 Locking knob.

18.5 Hand grip.

18.6 Lower datum edge.

18.7 Perpendicular working face.

18.8 Locking bolt (See Fig. N)

A. INSTALLING THE PERPENDICULAR

FENCE

Slide the T section guide (18.3) of the

Perpendicular Fence into the T slot (21) in the

planer base from the left as shown.

NOTE: It may be necessary to loosen the

locking knob (18.4) to allow the Locking

Bolt (18.8) to enter the T slot.

Tighten the locking knob to secure the

Perpendicular Fence in the desired position.

B. SETTING THE PERPENDICULAR FENCE

POSITION.

The Perpendicular Fence can be set in any

position across the planer width.

For wide material, the setting must expose

sufﬁcient planer blade to plane the full face

width.

For narrow material, the fence setting can

be altered to maximize blade life by using

different areas of the blade as it becomes

worn.

The fence position can also be used to set

rebate width (See Fig. K)

C. PLANING A PERPENDICULAR EDGE

The Perpendicular Planer will plane an edge

which is perpendicular to another face (usually

the wider face) of the work.

The work must be ﬁrmly clamped so that

both hands can be used to hold and guide the

planer.

Hold the planer on the edge to be planed

using the planer’s top handle in the normal

way.

Using the left hand, apply sideways force

to hold the face of the Perpendicular Fence

against the reference face of the work.

Plane in the normal way, but maintaining both

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX625 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,76 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX625 Manual

Product: